User S Instruction Manual For Plate Compactor-Books Pdf

USER S INSTRUCTION MANUAL FOR PLATE COMPACTOR
30 Jun 2020 | 1 views | 0 downloads | 18 Pages | 391.89 KB

Share Pdf : User S Instruction Manual For Plate Compactor

Download and Preview : User S Instruction Manual For Plate Compactor


Report CopyRight/DMCA Form For : User S Instruction Manual For Plate Compactor



Transcription

The purpose of this user s instruction manual is to provide safety information and operating instructions in order to. protect the user from exposed danger For your own safety please read the safety instructions and operating. instructions described in this manual thoroughly before use. THE INFORMATON CONTAINED IN THIS MANUAL IS BASED ON MACHINE IN PRODUCTION AT THE TIME OF. PUBLICATION NORTHERN INDUSTRAL RESERVES THE RIGHT TO MODIFY THE EQUIPMENT WITHOUT PRIOR. Please refer the following symbols as important remarks for the operation and maintenance. Indicates the warnings which must be precisely followed in order to prevent the plate compactor from being. damaged or destroyed, Indicates the danger which must be precisely followed in order to exclude the danger of personal injury. Indicates the important note or information which must be precisely perceived by the operator and the servicing. It is USER S RESPONSIBILITY to communicate proper information on the SAFE USE and GOOD. OPERATION of this machine Please contact your local NORTHERN industrial distributor or any of the contact. address in this manual directly for further information. Table of Contents, 1 Safety information 3, 2 Precautions 3. 3 Warnings 3, 4 Safety label locations 6, 5 Specifications 7. 6 Engine 8, 7 Operation 9, 8 Transportation 11, 9 Storage 12. 10 Periodic Maintenance Schedule 13, 11 Troubleshooting 13.
12 Component and Parts list 14, 13 Warranty Policy 17. 1 Safety Information, The product Plate Compactor is only allowed to be operated under the intended conditions of compacting ground where. vibrating roller is unable to compact It is prohibited to use it for any other purpose. Although the product is designed with special attention to the safety it is still the user s responsibility to read the safety. information THOROUGHLY AND CAREFULLY in this manual to avoid the exposed danger before use. The safety information in this manual alerts you to use the product safely without exposing in possible injury or damage. Do not modify or disassemble the product, 2 Precautions. 1 USERS MUST READ THE OPERATING INSTRUCTION IN THIS MANUAL CAREFULLY BEFORE USE. 2 KEEP THE UNAUTHORIZED INEXPERIENCED UNTRAINED PEOPE AWAY FROM THIS EQUIPMENT. 3 MAKE SURE ALL GUARDS SAFETY DEVICES ARE SECURLY PLACED IN THE ROTATING PARTS. 4 KEEP AWAY FROM THE DANAGER ZONE OF THE PLATE COMPACTOR. 5 DO NOT OPERATE THE PLATE COMPACTOR IN AN ENCLOSED AREA because its engine produces. carbon monoxide gas, 6 STOP THE ENGINE COMPLETELY AS DESCRIBED IN THIS MANUAL BEFORE SERVICING CLEANING. OR ADDING FUEL, 7 DO NOT REFUEL THE PLATE COMPACTOR NEAR THE FLAMMABLE MATERIALS It may cause fire.
8 BE CAREFUL NOT TO SPILL THE FUEL IN ENGINE and make sure to wipe off completely if spilled before. starting the engine, 9 DO NOT TOUCH THE MUFFLER DURING AND AFTER THE OPERATION because it generates mechanical. heat which might cause heat burn, 10 USERS MUST BE FULLY EQUIPPED WITH APPOROVED PROTECTIE EQUIPMENTS such as safety. helmet safety gloves safety shoes ear plugs safety glasses and mask and etc. 11 ALWAYS USE THE PROPER LIFITING CARANE TO MOVE OR LOAD THE EUQIPMENT Lifting in person. causes serious personal injury due to its heavy weight. FAILURES TO COMPLY WITH THE ABOVE PRECAUTIONS CAUSE SERIOUS INJURY. 3 1 To avoid fatal accident, 1 Stop the engine before refueling it and be careful not to spill the fuel during the refueling Spilled fuel may. cause fire, 2 Do not refuel the engine near inflammables to avoid fire. 3 Do not run the engine in an airtight space to avoid exhaust gas poisoning. 3 2 To protect the operator, 1 When operator feels the fatigue comes from vibration the operator must stop the machine and take a rest for a.
2 An airborne noise emission level of the equipment is about 70 95 dB apart 1 m 3 feet which requires to. wear ear protectors, 3 3 To avoid injury or damage. 1 The plate compactors are Only operated by authorized persons who. are aged at least 18 years, are physically and mentally able to handle the plate compactor. are properly trained in the operation and the maintenance of the plate compactor by the owner or its. authorized representative, are assessed to be able to carry out their duties reliably. 2 People who are drinking alcohol beverages and or taking drugs are not allowed to operate the plate compactor. 3 People are not allowed to enter into the danger zone of the plate compactor. 4 The operator has to monitor the danger zone all the time It is not allowed to operate if there is a person in the. danger zone, 5 Operate the plate compactor away from other workers because cracked and bounced rock may injure other. 6 The operator has to give warning signs in case of an emergency situation. 7 The plate compactor can only be operated when the adequate stability is granted. 8 The operator has to control the running speed of the plate compactor all the time during its operation so that. the plate compactor can be stopped at any time in order to avoid toppling. 9 The operator must turn off the plate compactor completely as described in this manual before leaving the. operating position Also the plate compactor must be secured against unauthorized use. 10 The engine has to be turned off and secured against re starting by pulling out the sparking plug socket during. the maintenance and servicing, 11 The operator has to control the plate compactor as regards functions and obvious defects before use.
12 Discovered defects must be reported to supervising personnel and to the operator Do not leave the defects. which may cause serious injury of the operator, 13 Do not operate the plate compactor when a defect endangers the safety of the operator until the defect is. 14 The compactor has to be checked by an expert in regular bases at least once a year And it must be checked. by an expert before the initial use and after the essential modification. 15 During the operation the operator has to monitor other objects within a radius of 20m in case of lighting. 16 The compactor generates mechanical heat so do not touch the body of engine muffler or other parts during. the operation which may cause heat burn Please wait until it cools down to touch. 17 The operator must be fully equipped with safety equipment including a crash helmet safety gloves safety. shoes safety glasses and mask before operating the compactor. 18 Do not insert your hand or finger between pulley cover and engine during the operation it may break your. hand or finger, 19 Sprinkle the water on the working area to avoid dust before operating but NEVER operate the plate compactor. if the working area is too wet because it may damage the life cycle of the product. 20 Do not transport the plate compactor with fuel in its fuel tank by the motor vehicle. 21 Do not lift the plate compactor by a person when putting on and off from vehicle Always use a proper lifting. crane to move Lifting by person may cause personal injury due to its heavy weight. 22 Make sure to securely fasten the compactor for transportation Improper fastening as holding the handle of the. compactor during the transportation may cause an injury. Please refer to the enclosed instruction manual of engine if there is a problem or a question on engine. before or during its operation, 4 Safety Label Locations. 5 Specifications, 5 1 Specifications, CE CERTIFIED PRODUCT ONLY. PLATE COMPACTOR, MODEL JPC 80, WEIGHT kg 86, PLATE SIZE mm 540 X 420.
TRAVEL SPEED m min 20 25, CENTRIFUGAL FORCE kgf 1 800. ENGINE As required, ENGINE OIL 10W 30 600CC, FUEL Unleaded Gasoline. KW HP RPM 4 0 4 5 5 5 6 0 3 600RPM, SHELL OMALA 100 OR SAE10W 30. VIBRATOR OIL, ORGIN Made in Korea, 5 2 Main parts of Plate Compactor. 5 3 Outline Configuration, 6 1 Recommended Fuel, 1 Plate compactor engine requires regular unleaded gasoline Use only fresh clean fuel Fuel containing water.
or dirt will damage the fuel system Consult to engine owner s manual for complete fuel specifications. 6 2 Before starting, 1 Read and understand the safety and operating instruction manual of the engine. 2 Check Point, Oil level in engine, Fuel level, Condition of air cleaner. Tightness of external fasteners, Condition of fuel lines. 6 3 Starting the Engine, 1 Shift the engine On Off switch to on. 2 Open the fuel valve, Note If the engine is cold move the choke lever to close position.
Note If the engine is hot set the choke lever at open position. 3 Move the throttle lever slightly to the left, 4 Pull the starter grip gently until resistance is felt then pull strongly. Note If the engine oil level is low the engine will not start. Note If the engine does not run check the oil level and add oil if needed. 5 Leave the engine run idle for 5 minutes for warm up. 6 Open the throttle fully to operate plate compactor. 6 4 Stopping the Engine, 1 Reduce the engine RPM to idle by moving throttle completely to the right. 2 Shift the engine On Off switch to off poison, 3 Close the fuel valve. Please see the instruction manual of engine for further detailed information. 7 Operation, All safety instructions must be read and observed clearly before starting to operate lack of clarity may. cause troubles of the equipment and cause personal injury. 7 1 Preparation for operation, 1 Check all the bolts nuts and belts If there is any looseness tighten it.
2 Check the oil level If the oil level is low add fresh oil. 3 Refill the gasoline Unleaded gasoline, 7 2 Operation. Several different kinds of engines are available upon request for this plate compactor and the followings. are for Honda GX160 engine made in Japan Please make sure to read the engine instruction manual. before operation, Please read the engine and plate compactor user s manuals before starting or operating this plate. 1 Check the fuel level engine oil and vibrating shaft oil. 2 Open the fuel valve and turn on the engine switch. 3 Set the speed control lever 1 3 to 1 2 of the way towards to high speed position in direction of arrow. 4 Choke the engine Note A warm engine may not need to be choked. 5 When starting the engine place one hand on compactor s handle and other hand on the engine starter rope. 6 Pull the starter rope in direction of arrow, 7 After starting Open the chock and allow engine to warm up at slow speed for 5 minutes. 8 Shift the speed control lever towards high position in direction of arrow after warm up to increase the speed. of engine to the required value, 9 To stop Set the speed control lever at low position in reverse direction of above figure and shift the engine. switch to off position, 10 Close the fuel valve, Whenever the high speed operation is NOT Required slow down the engine by moving the speed control lever.
to low position due to saving the fuel and extending the life of the equipment and avoiding injury. 7 3 Turing off the Engine, 1 Set the speed control lever at low position and leave the engine to run at low speed idle for 2 3 minutes. before stopping, 2 Turn off the engine switch as turns it into off position. Never stop the engine abruptly on its full speed, 3 Close the fuel valve. 4 Pull the starter grip slowly and return it to its original position when resistance is felt. Note The above operation is necessary to prevent outside moisture air from intruding into the. combustion chamber, If the engine has been running hard do not stop it abruptly from the full load. Cut down the speed load and allow the engine to run idle for a few more minutes. 8 Transportation, 1 Transport the plate compactor by vehicle or lift crane after securely fasten with rope or chain on the motor.
2 Make sure to hold the transportation grip or lifting lug properly when lifting plate compactor Holding the. handle for transportation may cause an injury, Do not transport the plate compactor with fuel in its fuel tank by the motor vehicle. Never lifting the plate compactor by a person especially when to put it on and off from the transporting. vehicle it may injure on person s back, To avoid burns or fire hazards let engine cool down before transporting it or indoor storage. Turn the fuel valve to off position and keep the engine level to prevent fuel from spilling. In case of storing the plate compactor for a long period of time for more than 30 days. 1 Remove the foreign substances such as soil stone or dirt from plate compactor and its engine. 2 Clean the engine cylinder cooling fins, 3 Clean or replace the air filter. 4 Change the engine oil and follow procedures described in engine manual for engine storage. 5 Cover it up with dry cloth completely for storage. 6 Store the plate compactor and its engine in a clean dry area. 10 Periodic Maintenance Schedule, Please refer to the following chart for the initial maintenance of plate compactor and its engine Also please see. the enclosed engine manufacturer s instruction manual for additional information about engine maintenance. The following chart is based on the normal operation schedule. Maintenance Interval Maintenance Point, Daily before operating Check the fuel level.
Check the engine oil level, Inspect the fuel lines. Inspect the air filter and replace it if needed, Check and tighten the external hardware. After the first 20 operating hours Check and adjust the drive belt. Change the engine oil, After the first 50 operating hours or every Check and adjust the drive belt. 4 keep away from the danager zone of the plate compactor 5 do not operate the plate compactor in an enclosed area because its engine produces carbon monoxide gas 6 stop the engine completely as described in this manual before servicing cleaning or adding fuel 7 do not refuel the plate compactor near the flammable materials it may cause

Related Books

AUCTION E VENTE Maison des ench res Salle des ventes

AUCTION E VENTE Maison des ench res Salle des ventes

Massey harris manure spreader 15 20 137 MECCANO Made in England Scout car N 673 15 20 138 MECCANO Made in England Austin champ N 674 15 20 139 MECCANO Made in England Canon SS medium Gum N 692 15 20 140 MECCANO Made in England Armoured personal carrier N 676 15 20

Basic Antenna Theory Wireless

Basic Antenna Theory Wireless

Basic Antenna Theory Ryszard Struzak Note These are preliminary notes intended only for distribution among the participants Beware of misprints ICTP ITU URSI School on Wireless Networking for Development The Abdus Salam International Centre for Theoretical Physics ICTP Trieste Italy 5 to 24 February 2007 R Struzak 2 Purpose to refresh basic physical concepts needed to understand

CHAPTER1 Managementboek nl

CHAPTER1 Managementboek nl

JWBS171 c01 JWBS171 Balanis November20 2015 7 6 PrinterName Trim 7in 10in CURRENT DISTRIBUTION ON A THIN WIRE ANTENNA 15 In order to animate and then visualize each of the three radiation problems the user needs MATLAB 11 andtheMATLABM file foundinthepublisher swebsiteforthebook toproduce

Antenna Theory Analysis and Design 4e by Balanis

Antenna Theory Analysis and Design 4e by Balanis

Section 9 8 of Antenna Theory Analysis and Design 4e by Balanis Figure 1 Antenna connected to a feeding transmission line Figure 2 Antenna impedance connected to a feeding transmission line Z 0 u l Z in Z A Z 0 u l Z A in Z in L other matches baluns docx 2 14 3 13 2020 Matching an antenna using a discrete parallel component As shown in Figures 1 and 2 we are seeking to

MAKALAH STRATEGIK SDM DALAM MENGHADAPI PERSAINGAN GLOBAL

MAKALAH STRATEGIK SDM DALAM MENGHADAPI PERSAINGAN GLOBAL

Abad 21 diwarnai oleh era globalisasi kesiapan pemerintah dalam menghadapinya perlu didukung oleh para pelaku bisnis dan akademisi Strategi SDM perlu dipersiapkan secara seksama khusunya oleh perusahan perusahan agar mampu menghasilkan keluaran yang mampu bersaing di tingkat dunia Perdagangan bebas tidak hanya terbatas pada ASEAN tetapi antar negara negara di dunia Situasi tersebut akan

Tantangan Pendidikan Tinggi Indonesia di Era Disrupsi dan

Tantangan Pendidikan Tinggi Indonesia di Era Disrupsi dan

Tantangan Pendidikan Tinggi Indonesia di Era Disrupsi dan Globalisasi Mayling Oey Gardiner Ketua Komisi Ilmu Sosial Akademi Ilmu Pengetahuan Indonesia Disiapkan untuk Seminar Nasional Kesiapan Sumber Daya Manusia Indonesia di Era Disrupsi dan Globalisasi sebagai kerjasama antara Akademi Ilmu Pengetahuan Indonesia dengan Universitas Padjadjaran Bandung 4 September 2018 Menanggapi

ACTIVITATE DE TIP INTEGRAT ADP ALA I ADE DLC si DEC

ACTIVITATE DE TIP INTEGRAT ADP ALA I ADE DLC si DEC

SARCINA DE LUCRU s urmareasc prezentarea ppt s povesteasc experien e personale legate de imaginile prezentate 7 SCENARIUL ZILEI Educatoarea preg te te sala de grup i materialele didactice naintea sosirii copiilor organizeaz centrele de interes i col ul cu surpriza zilei Ziua debuteaza cu Intalnirea de dimineata rutine salutul prezenta calendarul zilei

EXEMPLE DE BUNE PRACTICI Accesorii barca

EXEMPLE DE BUNE PRACTICI Accesorii barca

fi e de lucru calculator videoproiector foi de flip chart foi de h rtie RESURSE DE TIMP 1 or de curs Scenariul temei Secven a introductiv Preg tirea clasei cu cele necesare Se verific dac sunt absen i Se distribuie materialele Captarea aten iei elevilor Profesorul enun c teva cuget ri A cunoa te pe al ii este o mare tiin dar cunoa terea de sine este

PROIECT DE ACTIVITATE INTEGRAT timtim timy

PROIECT DE ACTIVITATE INTEGRAT timtim timy

s respecte etapele de lucru exers nd deprinderile tehnice nsu ite anterior s i poat autoevalua lucrarea i aprecia corect lucr rile celorlal i s i dezvolte gustul estetic i creativ STRATEGII DIDACTICE METODE I PROCEDEE explica ia exerci iul conversa ia MATERIALE DIDACTICE siluete cu pui ori vase cu aracet lop ele granule m lai h rtie creponat

ALEGE O MESERIE timtim timy ro

ALEGE O MESERIE timtim timy ro

s coloreze fi e de lucru ce reprezint meserii respect nd conturul i culorile Strategii didactice Metode i procedee observa ia conversa ia explica ia exerci iul Material didactic coli culori carioca fise reprezent nd diferite meserii Evaluare Turul galeriei 3 CENTRUL DE INTERES JOC DE ROL Tema De a doctorul Obiective opera ionale s desf oare jocul de

CAIET DE PRACTIC PEDAGOGIC PENTRU NV M NT PRE COLAR

CAIET DE PRACTIC PEDAGOGIC PENTRU NV M NT PRE COLAR

de lucru fi e de analiz grile de observare protocoale de observa ie au fost grupate n urm toarele categorii informa ii legate unitatea coalar structur cultur curriculum informa ii legate de pre colari informa ii legate de rolurile i responsabilit ile cadrului didactic Scopul prezent rii acestor instrumente de lucru este ca n urma utiliz rii lor de c tre