This Manual Was Printed From A Pdf And Was Not Included -Books Pdf

This manual was printed from a PDF and was not included
13 Feb 2020 | 7 views | 0 downloads | 26 Pages | 468.86 KB

Share Pdf : This Manual Was Printed From A Pdf And Was Not Included

Download and Preview : This Manual Was Printed From A Pdf And Was Not Included

Report CopyRight/DMCA Form For : This Manual Was Printed From A Pdf And Was Not Included


Thank you for choosing CMMG Inc, Please follow all instructions in this manual before operating. Fundamental Firearm Safety Rules, 1 Always keep the firearm pointed in a safe direction. 2 Always keep your finger off the trigger until ready to. 3 Always keep the firearm unloaded until ready to use. 4 Be sure the firearm is safe to operate,5 Know how to use the firearm safely. 6 Use only the correct ammunition for the firearm,7 Know the target and what is beyond. 8 Wear appropriate eye and ear protection, 9 Never use alcohol or drugs before or while shooting.
10 Store firearms so that they are not accessible to. unauthorized persons, 11 Be aware that certain types of firearms and many. shooting activities require additional safety precautions. Failure to follow these rules can result in damage to property. injury or death Always follow these instructions and carefully. read and refer to this manual before loading firearm. This is NOT a safety manual, If you need assistance with the safe handling of this or any firearm. please contact a certified firearms instructor or school. Table of Contents,Operating Procedures,Unloading and Clearing Your Rifle 1. Loading and Firing Your Rifle 3,Zeroing Your Sights 5. Basic Care and Maintenance,Disassembly Instructions 7.
Upper Maintenance 10,Bolt and Carrier Maintenance 12. Lower Maintenance 13,Reassembly Instructions 14,Function Check 15. Warranty Information 16,Ammunition Warning 17,Trouble Shooting Guide 19. Contact Information 23, Please familiarize yourself with this manual and the operation of your. particular firearm To ensure that you get the best performance and. reliability from your new CMMG firearm please read through all of the. procedures listed in this manual before attempting to perform any of. the described actions If any part of this manual is unclear to you. please contact us before attempting the procedure, All complete firearms and uppers are headspaced and test fired.
before shipping, Clean your firearm before using for the first time. Unloading and Clearing Your Rifle,To unload your rifle. 1 Keep your rifle pointed in a safe direction for the duration. of the procedure,2 Place your selector on SAFE You cannot select. SAFE unless the hammer is cocked, 3 Depress the magazine catch button and remove the. 4 Eject the chambered cartridge by retracting the charging. handle until it stops Let the ejected cartridge fall to the. Unloading and Clearing Your Rifle, 5 Lock the bolt open by depressing the bottom of the bolt.
catch If you cannot manipulate the charging handle and. the bolt catch at the same time you can use an empty. magazine which will activate the bolt catch for you. 6 Push the charging handle forward until it clicks to re latch. the charging handle, 7 Inspect the chamber and receiver to ensure you have. removed all cartridges from the action, Your rifle is now Unloaded and Clear It may now be loaded or. prepped for transportation or storage,Loading and Firing Your Rifle. To load and fire your rifle, Begin with a rifle that has been verified to be unloaded using the. preceding directions, 1 Keep your rifle pointed in a safe direction for the duration.
of the procedure, 2 Load your magazine with 223 Remington or 5 56x45. NATO cartridges Place cartridge between the,magazines feed lips and push down to seat. 3 Using firm and steady pressure insert the loaded. magazine into the magazine well until the magazine. catch locks the magazine in place Do not slam the, magazine into position it will damage your magazine and. rifle Pull the magazine down to verify that it is locked in. 4 Get into the shooting position you plan to use Grasp the. pistol grip in one hand and the handguard in the opposite. hand with the buttstock to your shoulder, 5 To chamber a cartridge you may depress the bolt catch. or retract the charging handle until the bolt is no longer. being held by the bolt catch Release the charging, handle Do not maintain control the of the charging.
handle while chambering a cartridge this will cause the. rifle to jam,Your rifle is now loaded,Loading and Firing Your Rifle. The following is a description of the sequence for one complete. firing cycle beginning after a cartridge is chambered Knowing. the correct function of your rifle will help you with the diagnosis. of any malfunctions or failures to fire, The trigger is pulled releasing the hammer which strikes the. firing pin The firing pin impacts the primer in the chambered. cartridge igniting the primer which ignites the powder As the. powder is burned it creates a high volume of gas which propels. the bullet down the bore of the barrel The exhaust gas is also. vented out of the bore through the barrel s gas port into the. front sight base and through the gas tube and into the carrier. key on the bolt carrier The gas pushes the bolt carrier back. unlocking your bolt from the barrel extension allowing the bolt. carrier to recoil completely The underside of the bolt will push. the hammer down where it is caught and held by the. disconnector The bolt will pull the spent cartridge out of the. chamber and eject it from the rifle, At full recoil the carrier has pushed the buffer and buffer spring. back into the receiver extension The magazine will present a. new cartridge which will be stripped from the magazine by the. bolt as the recoil spring pushes the bolt carrier group back into. battery The new cartridge is now chambered The fire control. group will reset once you have released the trigger allowing the. disconnector to release the hammer and re engage the trigger s. sear The rifle is ready to be fired again or put on SAFE and. 6 Align your sights on your target, 7 Place the selector on FIRE Your rifle is now ready to. 8 Squeeze the trigger until the hammer is released. Zeroing Your Sights,U S Marine Corps,25 Meter Zeroing Procedure.
By following the steps below and establishing a zero at 25 meters. using a 25 meter sight in target your rifle sights will be set with a 300. meter battlesight,Do not move front sight post at,this time it was set at the factory. and should be very close to your,zero The rear sight aperture. should also be centered from the,factory with the unmarked large. aperture up If the aperture is,not centered turn the windage. knob clockwise to adjust the,aperture to the right or counter.
clockwise to adjust the aperture,to the left until centered this is. called mechanical zero, 1 Rotate elevation knob in the down direction counter. clockwise The elevation knob should stop three clicks past. the 300 meter mark The rear sight should be all the way down. on the last whole click before it bottoms out This is called. mechanical zero elevation for the rear sight If your range. scale will not line up in the above manner an armorer will be. required to adjust the range scale for you, 2 Rotate the elevation knob up one click past the 300 meter. mark From this point on the rear sight elevation knob should. not be moved Any changes in elevation required in the. following zeroing steps are made to the front sight post only. 3 Carefully aim and fire at the center of the,target bull s eye Take your time and be. sure to use the sight picture illustrated,Zeroing Your Sights.
4 If your shot group is not in the center of the bulls eye use the. squares on the target sheet to calculate the required clicks. necessary to move your next shot group into the bulls eye. Changes in elevation are made by moving the front sight post The. squares are numbered around the edges of the target to equal the. number of clicks required to move the shot group to the bull s eye In. order to raise your next shot group rotate the front sight post. clockwise One click will move the strike of the bullet one vertical. square on the target sheet In order to lower your next shot group. rotate the front sight post counter clockwise One click as above. equals one square, Changes in windage are made with the windage knob Three clicks. will move the strike of the bullet one horizontal square on the target. sheet In order to move the shot group to the left turn the windage. knob counter clockwise In order to move the shot group to the right. turn the windage knob clockwise, 5 Carefully aim and fire another group at the center of the target. bulls eye Repeat steps 3 through 5 if required, If your group is on target your sight is now calibrated To place your. actual 300 meter zero on the rifle you must rotate the elevation knob. one click down The range scale s 300 meter mark should now be. aligned with the mark on the receiver, This manual was printed from a PDF and was not included with. an original CMMG Rifle If you have any doubts as to the. authenticity of the any rifle that came with this manual please. contact us,Disassembly Instructions, Before disassembling your rifle please unload and clear your.
rifle as described in the unloading directions, 1 Reverify your rifle is unloaded and return the bolt and. carrier in to battery,2 If you need to remove the handguards it is. easier to do so while the upper is joined to,the lower The handguards can remain in. place for all end user maintenance Place,the butt of the rifle on a solid surface Pull. down on the Delta ring with even tension,on each side at the same time pulling one.
section of the two piece handguard away,from the other Set the first half aside and. repeat the process for the remaining half, 3 Partially push the rear take down pin and the front pivot. pin from left so they are not captured by the detents that. retain them in the receiver in the closed position Use a. Delrin Take down Pin Punch if needed,4 Pull the rear take down. pin the rest of the way,to the right side of the,lower receiver until it. engages the detent,that holds the pin in the,open position.
5 Pivot the lower receiver away from the upper receiver. 6 Pull the front pivot pin the rest of the way to the right side. of lower receiver until it engages the detent that holds the. pin in the open position,Disassembly Instructions, 7 The upper and lower receivers are now separated set. the upper receiver aside, 8 Remove the buffer and buffer spring from the lower. receiver by depressing the buffer detent Maintain tension. on the buffer face while removing,it is under pressure from the recoil. spring You may need to hold the,hammer down to allow the buffer. and spring to be removed from,receiver extension, 9 Set the lower receiver buffer and recoil spring aside and.
pick the upper receiver back up, 10 Pull the charging handle to rear and remove bolt and. carrier assembly Set the bolt and carrier assembly aside. 11 Remove the charging handle by pulling it backwards until. it is aligned with the key way The charging handle may. now be lifted from the upper receiver, 12 Set the upper receiver and the charging handle aside and. pick the bolt carrier assembly back up,13 Disassembly Instructions. 14 Remove the firing pin retaining pin from the left side of. the bolt You may use a small screwdriver or punch to. hook the loop the end of the firing pin retaining pin. 15 Tilt bolt face up and remove firing pin from the rear of the. bolt carrier, 16 Push bolt into the carrier until it rotates and comes to a. stop in battery position, 17 Turn cam pin 90 and lift it out from bolt and carrier.
18 Pull bolt forward out of carrier Set the carrier aside. 19 With a punch remove the extractor pin from the bolt. assembly Slight pressure applied to the extractor will. ease removal of the extractor pin,20 Remove the extractor The extractor spring and. elastomer insert should be captured in the extractor do. not remove the spring and elastomer from the extractor. Your rifle is now field stripped for cleaning, Do not disassemble your firearm any further than described. Any maintenance that requires further disassembly should be. performed by CMMG or a qualified gunsmith,Basic Care and Maintenance. Proper maintenance will ensure you get the best performance. from your firearm High quality cleaning products will ensure. that you get your rifle clean quickly and without damage to your. firearm The Mil Spec cleaning kit is great for field use but a. good set of cleaning tools and a one piece cleaning rod will. make your task easier at home There are also many excellent. cleaning products available to shooters today We do not. recommend any specific brand so use what you like Just. make sure that it is safe to use on the parts you are cleaning. Upper Maintenance, 1 Use cleaning fluid on the bore and chamber the gas. tube the upper receiver and, barrel assembly locking lugs and all areas of powder.
fouling corrosion dirt or dust, 2 Install the chamber brush on the cleaning rod dip the. brush in cleaning fluid and insert it into the chamber and. locking lugs Clean by pushing and twisting the cleaning. 3 Install the bore brush on the complete cleaning rod Dip. the brush in cleaning fluid Run the rod through the. chamber and flash suppressor or muzzle brake several. 4 Take the bore brush off the rod and install a swab holder. and a swab Apply cleaning fluid, to the swab then run it through the chamber and out the. flash suppressor if applicable To, remove carbon build up let the solvent sit then wipe. clean Wipe the bore dry by running clean swabs all the. way through from the chamber to the flash suppressor. 5 Once the patches come out dry they should be clean If. not repeat steps 3 and 4,Upper Maintenance, 6 Use a worn out bore brush to clean the outside surface of. the protruding gas tube, NOTE Heat will discolor your gas tube do not try to.
remove this discoloration, 7 Wipe the charging handle with a patch dipped in solvent. wipe off solvent with a dry cloth, 8 Inspect the upper assembly for any worn broken or. damaged parts Replace any faulty parts with quality. CMMG replacement parts, 9 Lightly lubricate the bore and chamber outer surface of. the barrel and front sight under the handguards and the. charging handle, 10 With a lubricated swab run the rod from the receiver to. the flash suppressor or muzzle brake Do not over,11 Lubricate the locking lugs.
12 Drip lubricant onto the front sight detent Then depress. the detent to work the lubricant in,13 Reassemble upper. Bolt and Carrier Maintenance,WARNING Never interchange bolts between rifles. 1 Clean all parts and outer surfaces of the bolt carrier. assembly with a swab saturated with cleaning fluid. 2 Clean the bolt carrier key with a worn bore brush dipped. in cleaning fluid and dry with a pipe cleaner, 3 Remove carbon deposits and dirt from the locking lugs. with a cleaning brush dipped in cleaning fluid, 4 Clean the areas behind the bolt rings and under the lip if. the extractor, 5 Press the ejector in repeatedly to remove accumulated.
brass shavings from the ejector hole and assure the. ejector moves freely, 6 Inspect the bolt assembly for cracks or fractures. especially in the cam pin hole area Inspect the firing pin. retaining pin for bends breaks or dents Inspect the bolt. cam pin for cracks or chips Inspect the firing pin for. bends cracks or a sharp chipped or blunted tip, 8 Lubricate the bolt carrier bolt cam pin firing pin and. firing pin retaining pin Be sure to coat the inner and. outer surfaces and the cam pin area of the bolt carrier. Place one drop of lubricant inside the key Flush the. ejector with lubricant and cycle the plunger enough to. ensure the ejector spring is well lubricated,9 Reassemble bolt and carrier.

Related Books



1953 the first edition of Merck's Microbiology Manual was printed. It included 85 dehydrated culture media. The new manual The new Manual is the the 12th edition of the Merck Microbiol-ogy Manual and replaces all former editions. This Manual is available as hard copy and in digital form on CD-ROM. The 12 th edition greatly differs from the 11 ...

British Flat Pattern and Listed Races 2014

British Flat Pattern and Listed Races 2014

An Introductory Manual For Affirmative Action Officers

An Introductory Manual For Affirmative Action Officers

- Conduct a student survey every three years to find out what their sports interests are before planning new programs. (See attached sample, page 26-27). Other Areas - Examine guidance tests for bias. - Review work study placements of males and females. - Identify inequities in club participation, awarding of scholarships, etc.

Acoustic study of sandwich panels for use in aeronautic ...

Acoustic study of sandwich panels for use in aeronautic

performed using FEM simulations, in the commercial program Ansys. The acoustic behavior of sandwich panels is predicted from the Transmission loss frequency plots obtained from three different setups developed in this work: acoustic cavity (ideal), suspended panel surrounded by fluid

MATE Server Installation Guide -

MATE Server Installation Guide cisco com

iii MATE Server Installation Guide CONTENTS Overview 1-1 For More Information 1-1 Before You Start 2-1 Terminology 2-1 Plan File 2-1

Visualising and Assessing Acceptance Sampling Plans: The R ...

Visualising and Assessing Acceptance Sampling Plans The R

conformity, single sampling, double sampling, multiple sampling, attributes sampling, 2-class, variables s4 methods. 1. Introduction Acceptance sampling is a methodology commonly used in quality control and improvement. The aim is to make an inference about the quality of a batch/lot of product from a sample.

Operating Characteristic Curves for Acceptance Sampling ...

Operating Characteristic Curves for Acceptance Sampling

window, load the Operating Characteristic Curves for Acceptance Sampling for Attributes procedure window by clicking on Quality Control and then clicking on Operating Characteristic Curves for Acceptance Sampling for Attributes. You may then make the appropriate entries as listed below, or open Example 1(a or b)



is lost, a duplicate should be obtained from FIORENTINI. failure to comply with the instructions in this manual. FIORENTINI reserves the right to introduce any required technical and commercial changes without giving any notice. Therefore, any data and information contained in this manual may be changed and/or updated.



procedures indicated in the manual. When commissioning, the risks associated with any discharges into the atmosphere of flammable or noxious gases must be assessed. In installations in natural gas distribution networks, the risk of the formation of explosive mixtures (g as/air) inside the piping must be considered.

Peer Review Documents -

Peer Review Documents OECD org

BEPS Action 14 on More Effective Dispute Resolution Mechanisms . PEER REVIEW DOCUMENTS . October 2016