Installation Tips For Your Excalibur Remote Start For-Books Pdf

Installation Tips for your Excalibur Remote Start for
02 Jul 2020 | 3 views | 0 downloads | 14 Pages | 922.22 KB

Share Pdf : Installation Tips For Your Excalibur Remote Start For

Download and Preview : Installation Tips For Your Excalibur Remote Start For


Report CopyRight/DMCA Form For : Installation Tips For Your Excalibur Remote Start For



Transcription

The location of the wire in the car, The illustrations below will show you where to find that information on your chart. Making your wiring connections, The tables on the next 2 pages show you where to connect the wires from your remote start into the car Any wires on. your remote start that are NOT listed in the table are NOT USED. Helpful Hint In most cases the wires on the remote start are way longer than needed Trim off excess wire when you. make your connections but leave some slack this will allow you a little flexibility when it comes time to stow the. remote start module after the installation is completed See Installer s Tip 2 on Page 5 for tips on how to make your. wiring connections, For EXCALIBUR Remote Starts, Remote Start Wire Connect to the wire for the circuit on the vehicle chart labeled. Red White 6 pin harness Constant 12 Volts, Red 6 pin harness Constant 12 Volts. Pink White 6 pin harness Ignition 12 Volts, Violet 6 pin harness Starter.
Orange 6 pin harness Accessory, Pink 6 pin harness Ignition 2 not present on all vehicles. Blue 3 pin harness Unlock wire, Green 3 pin harness Lock wire. White Black 12 pin harness Parking Lamp IMPORTANT SEE NOTE 1. White 12 pin harness Parking Lamp IMPORTANT SEE NOTE 1. Black 12 pin harness System Ground connect this to a solid metal ground in the car. Brown Red 12 pin harness Brake Light also called Brake Switch. Black White 12 pin harness Neutral Safety if you have an automatic transmission ground this wire. Grey 12 pin harness Hood Input See NOTE 2, The connections below MAY be needed. Light Green Red 12 pin harness OEM Alarm Disarm connect this if your car has a factory alarm system. Violet White 12 pin harness Tach Signal See NOTE 3. NOTE 1 The remote start has two parking light wires You will only use one of them On your vehicle wiring. chart look up the wire for the parking lights Next to the wire color will be either a or a If yours has. the then use the white wire If it has a use the white black wire. NOTE 2 The grey wire is used with a pin switch included in your kit to prohibit the remote start from activating. while the hood is open This is an important safety feature. NOTE 3 Most vehicles will not require this connection The remote start has a tach sensing circuit built in. The purpose of that circuit or the tach wire if you need it is to enable the remote start to detect when the. engine has started so it will stop cranking the starter When you test your system if the starter keeps cranking. after the engine has started you ll need to connect the tach wire Once the wire is connected take two. additional steps 1 Change Installer Programming Option 2 to the tach wire setting see page 11 in the. installer s manual 2 Program the tach circuit as shown on page 10 of the installation manual. Your kit also includes a programming button Plug the button into the remote start For tips on where to install the. button see Installer s Tip 1 on Page 5, TRUNK RELEASE NOTE If your vehicle has a positive trigger trunk release we have included a relay with your kit. Refer to the following diagram for instructions on how to connect the relay that will enable your remote trunk pop. If you see a next to trunk release on your wiring diagram you will not need the relay and can connect the aux output. wire from the remote start directly to the trunk release wire in the vehicle. If there is no data for trunk release in your wiring chart then you have a manual pull cable release that cannot be. controlled by the remote start, NOTE the 12V source can be taken from the red wire on the 12 pin harness Pin 87a on the relay is not used Cut and.
cap that wire, Installing your bypass, The IBH34 bypass connections will vary depending on the specific model Honda Acura Refer to the installation. instructions for the IBH34 that are included at the end of this document There you will be able to see which wiring. configuration is used for your car, Here are some tips that are applicable regardless of which configuration you use. The red plug on the end of the brown wire gets plugged in to the Sat Relay Port of your remote start This is. how the remote start activates the bypass when it is needed. The Red wire gets connected to a constant 12v power source You can tap it directly on to the large red wire in. the remote start s 6 pin harness, The Black wire goes to ground. Suggestion If possible avoid using tap connectors on the Data wires coming off the key lock cylinder connector The. wires are small and sometimes a tap connector won t make good contact We suggest you either wrap and tape or. solder and tape these connections See Installer s Tip 2 on page 5. Step 2 Program the Bypass, Instructions for programming your bypass are in the IBH34 installation manual Programming is easy and only takes a. few seconds You will need to have one valid key for programming. Step 3 Test the System, Once all your connections are made and the bypass is programmed you should test the system before putting.
everything back together, 1 Remove your keys then close the doors. 2 Press the lock and unlock buttons on the new remote fob Make sure they control your door locks. accordingly, 3 If you have connected the remote trunk pop feature make sure that functions properly. 4 Press the start button on the remote start s keyfob This should start the car Pressing the start button again. should shut it down, 5 Start the car again then open the door and step on the brake pedal That should shut the car downagaon. Step 4 Close it Up, Once the bypass has been programmed give the system one final test. Now gather up all your wiring and neatly bundle it together using zip ties or electrical tape Find a secure place to put. the remote start module and use zip ties to secure it Make sure that the remote start wires are not near any moving. parts on the steering wheel pedals or emergency brake. Installer s Tips, Tip 1 Where Everything Goes, There are 4 parts to your system.
1 Remote start module the wiring for the module is done under the dash on the driver s side so you ll want to. install the module in that general area Before you start wiring look for a location where there s some open. space that will fit the module Pay attention to moving parts like the pedals e brake and steering column Be. sure to route your wiring away from those areas, 2 Bypass module can be stowed along with the remote start. 3 Programming button Requires a small screw hole Usually put in the driver s kick panel that s the area. forward of the door the driver s side of the center console or the underside of the dash. 4 Hood Pin Switch An important safety component Requires a 3 8 hole Find a location in the engine. compartment to mount the switch where the closed hood will keep the plunger in the switch depressed This is. what prevents the car from starting when the hood is open. Tip 2 How to make your wiring connections, It s very important that all your wiring connections be solid and secure All remote start connections are tap on. connections This means that you do not need to cut the wires in the car You simply need to tap on to the wires in the. car to make your connections Here are three different ways to do this. Method 1 Solder and tape, This is the method preferred by the best professional installers It makes for the most reliable connections but it is also. the most difficult to do Sometimes there isn t enough room in the wiring harness to safely solder a wire without. damaging adjacent wires but if you have the soldering skills go for it To make a connection strip back a section of the. insulation on the wire in the car On heavy gauge wires 1 is about the right amount On lighter gauge wires is fine. Strip 1 of insulation off the end of the remote start wire Tin the bare section of wire in the car Wrap the remote. start wire around the tinned section and then carefully solder it in place Wrap the splice tightly with electrical tape. Method 2 Wrap and tape, This is the most popular method and is also very reliable Strip back a section of the insulation on the wire in the car. On heavy gauge wires 1 is about the right amount On lighter gauge wires is fine Strip 1 of insulation off the end. of the remote start wire Separate the strands of the wire like this. Pass the wire from the remote through the opening as shown below. Wrap the remote start wire around both sides of the car wire then back around itself as shown below. Use electrical tape to wrap the connection and secure the wires together A wire tie will help prevent the tape from. unraveling in the future, Method 3 T Taps, T taps are plastic clips that are squeezed onto the wires in the car The wire from the remote start goes into the tap.
and the whole thing is crimped together T taps come in different sizes for different size wires Use yellow t taps for. the larger wires in your main power harness Red t taps are good for the smaller wires Tape and wire tie the. connections as shown in the wrap and tape section above that will prevent the t taps from ever opening up. We now have a tap kit available for purchase for those who prefer to use this method The kit consists of two types of. connectors The taps and insulated male spade connectors that plug into them The taps attach to the wires in the car. and the spade connectors attach to the wires on the remote start The spades then plug in to the taps A crimping tool. is required, Copyright 2011 Digitel LLC, Did you find this document helpful Please let us know so we can continue to. improve our service to you Suggestions are welcomed and encouraged. Please email to sales mypushcart com, MODEL PKH34, Rev 20110106. transponder, MODEL PKH34, HONDA ACURA TRANSPONDER DATA. OVERRIDE INTERFACE NO KEY REQUIRED, INSTALLATION GUIDE. PRODUCT DESCRIPTION, PKH34 is a fixed Honda and Acura Transponder Data Override Interface solution that works on.
all 2005 09 Honda and Acura vehicles including select 2001 2004 models 100 compatible. with any remote start system PKH34 is also the first BYPASSKIT fixed firmware solution to. add an enhanced data security override activation port D2D The D2D activation port takes. the PKH34 BYPASSKIT to another level of enhanced security when paired with any remote. start system using the D2D communication protocol D2D data to data is the same. communication protocol used with the XPRESSKIT line of programmable vehicle modules. however in the case of the PKH34 the data port is used solely as secure data activation input. when paired with a similarly equipped D2D remote start system Security of the override. module is enhanced by disabling all analogue inputs whenever the module detects. communication with a D2D enabled remote start system This prevents the override feature. from being activated by any other method other than the remote start system. PRODUCT FEATURES, Enhanced D2D functionality provides a secure single wire data override. Compatible with any remote car starter, Compatible with manufacturer s anti theft security system. Maintains integrity of manufacturer s anti theft immobilizer system. Compact design easy to mount, No Key Required for operation NKR. Simple programming, All temperature operation, Honda and Acura are registered trademarks and property of their respective companies. 2008 Directed Electronics All rights reserved, MODEL PKH34.
4 PIN DATA TO DATA D2D CABLE, INPUT Brown Ground When Running status. Remote Control, N C N C Green N C, N C N C Blue N C. N C N C Violet White N C, DATA Violet Data, INPUT Pink White Security Light Key Side. OUTPUT Pink Security Light ECM Side, INPUT Orange Ignition. INPUT Red 12 Volt Constant, Transponder Data Override Interface.
INPUT Black Chassis Ground 12VDC, INSTALL A Honda Acura Type C. WIRE SIDE OF 1 2 3 4 5 6 7, page 1 to 2, Rev 20110106. 2008 Directed Electronics All rights reserved, INSTALL A WIRE GUIDE CONNECTIONS. 10 PIN HARNESS D2D Optional use of 4 Pin Data to Data D2D cable will replace the analogue wire w2w connection. MODEL PKH34, WIRE D2D I O Connect, COLOR w2w STATUS Location SPECIFIC WIRE CONNECTION LOCATION ACTIVATION and or FUNCTIONALITY. 1 Brown D2D Input RCS Ground When Running status Output of RCS Immobilizer Bypass Via Data. 2 Green N C N C N C N C N C N C, 3 Blue N C N C N C N C N C N C.
4 Violet N C N C N C N C N C N C, 5 Violet w2w Data Vehicle Connect to vehicle Data wire PIN 2 Data Commands from Module to Vehicle. See Vehicle Wiring Reference Chart for wire colors. 6 Pink w2w Input Vehicle Connect to vehicle security light wire PIN 5 Key Side Security Light Power Source Return. White See Vehicle Wiring Reference Chart for wire colors. 7 Pink w2w Output Vehicle Connect to vehicle security light wire PIN 5 ECM Side Security Light Power Source Supply. See Vehicle Wiring Reference Chart for wire colors. 8 Orange w2w Input Vehicle Ignition Input Source Ignition Input Source. 9 Red D2D Input Vehicle Constant 12 Volt Source Power Source. 10 Black D2D Input Vehicle Chassis Ground Ground Source. Legend RCS Remote Control System N C No Connection N A Not Applicable W2W analogue wire to wire D2D data 2 data. page 2 to 2, Rev 20110106, 2008 Directed Electronics All rights reserved. MODEL PKH34, Rev 20110106, INSTALL A VEHICLE WIRING REFERENCE CHART. VEHICLE DATA IGNITION GROUND SECURITY LIGHT, Acura EL 1 7 Red Blue Yellow Black Brown Yellow Blue Orange. Installation Tips for your Excalibur Remote Start for Honda and Acura Vehicles Thank you for purchasing your remote start from MyPushcart com an industry leader in providing remote starts to do it yourself installers since 1999 We ve put this tip sheet together to help you with your installation The purpose of this sheet is to help you organize your installation not to replace your

Related Books

Regulation Availability of and Collection of Checks

Regulation Availability of and Collection of Checks

The term check does not include checks drawn in a foreign currency or checks drawn on a bank located outside the United States Regulation CC Availability of Funds and Collection of Checks Background Regulation CC 12 CFR 229 implements two laws the Expedited Funds Availability Act EFA Act which was enacted in August 1987 and became effective in September 1988 and the Check

Installation Operation amp Maintenance Manual Quality Lifts

Installation Operation amp Maintenance Manual Quality Lifts

Installation Operation amp Maintenance Manual Four Post Surface Mounted Lift Models Q4P07 7 000 lb Capacity 200 Cabel Street P O Box 3972 Louisville Kentucky 40201 3972 Email sales qualitylifts com Web site www qualitylifts com Office 877 771 5438 502 583 5438 Fax 502 583 5488 IMPORTANT READ THIS MANUAL COMPLETELY BEFORE INSTALLING or OPERATING LIFT Model Q4P07 Installation Operation

INSTALLATION OPERATION MAINTENANCE ANUAL Quality Lifts

INSTALLATION OPERATION MAINTENANCE ANUAL Quality Lifts

ANUAL Two Post Surface Mounted Lift M ODEL Q12 12 000 LBS C APACITY 3000 LBS PER A RM 200 Cabel Street P O Box 3944 Louisville Kentucky 40206 Email sales qualitylifts com Web site www qualitylifts com Office 877 771 5438 502 583 5438 Fax 502 583 5488 IMPORTANT READ THIS MANUAL COMPLETELY BEFORE INSTALLING or OPERATING LIFT Model Q12 Installation Operation and Maintenance Page 2

DEH S6000BS Owner s Manual DEH S6010BS

DEH S6000BS Owner s Manual DEH S6010BS

CD RDS RECEIVER AUTORADIO CD RDS REPRODUCTOR DE CD CON RECEPTOR RDS DEH S6000BS DEH S6010BS Owner s Manual Mode d emploi Manual de instrucciones Important Serial number The serial number is located on the bottom of this unit For your own security and convenience be sure to record this number on the enclosed warranty card Important Num ro de s rie Le num ro de s rie se trouve au

Gastrointestinal Motility Disorders Diagnosis and

Gastrointestinal Motility Disorders Diagnosis and

Gastrointestinal Motility Disorders Diagnosis and Treatment 43882 64590 64595 Physical findings Results of diagnostic tests and imaging studies Co morbidities Medical treatments tried failed and contraindicated Current physician treatment plan if applicable For code descriptions see the Applicable Codes section

Mental Health Policy and Service Guidance Package ADVOCACY

Mental Health Policy and Service Guidance Package ADVOCACY

Mental Health Policy and Service Guidance Package Advocacy is an important means of raising awareness on mental health issues and ensuring that mental health is on the national agenda of governments Advocacy can lead to improvements in policy legislation and service development

Agilent Oligonucleotide Array Based CGH for Genomic DNA

Agilent Oligonucleotide Array Based CGH for Genomic DNA

Agilent Oligonucleotide Array Based CGH for Genomic DNA Analysis Bravo Automated Liquid Handling Platform with Enzymatic and ULS Labeling Protocol Version 2 3 August 2015 For Research Use Only Not for use in diagnostic procedures

MEMORANDUM FOR SUPPLY PROCESS REVIEW COMMITTEE PRC MEMBERS

MEMORANDUM FOR SUPPLY PROCESS REVIEW COMMITTEE PRC MEMBERS

MEMORANDUM FOR SUPPLY PROCESS REVIEW COMMITTEE PRC MEMBERS SUBJECT Approved Defense Logistics Management System DLMS Change ADC 1040 Migrate Inter Service Ammunition Serial Number and Lot Number Transactions NA VSUP P 724 Document Identifier Code DIC BG 1 BG2 to DLMS 945A Materiel Release Advice The attached approved change to Defense Logistics Manual DLM 4000 25 Defense

NEW HOLLAND AG DEALERS WITH MRT AGREEMENT PowerStar 75

NEW HOLLAND AG DEALERS WITH MRT AGREEMENT PowerStar 75

NEW HOLLAND BRAND PRODUCTS U S NO 19 62A NEW HOLLAND AG DEALERS WITH MRT AGREEMENT SUBJECT POWERSTAR SERIES PRICE amp DATA PAGES EFFECTIVE 12 09 2019 The agricultural industry is constantly evolving to meet the world s shifting needs Here at New Holland we re focused on matching pace with those changes to help you get the job done

IN COMMERCIAL HAY PRODUCTION PRECISION LAND MANAGEMENT PLM

IN COMMERCIAL HAY PRODUCTION PRECISION LAND MANAGEMENT PLM

IN COMMERCIAL HAY PRODUCTION success is dependent on speed efficiency and precision from both you and your equipment especially with large acres of field crops to harvest and animals to feed At New Holland we engineer and supply the innovative equipment with technology that saves you time and money as you produce the highest quality hay and forage Our goal Make every bale the best it

The farming specialist with a wide CNH Industrial

The farming specialist with a wide CNH Industrial

The farming specialist with a wide agricultural equipment offering and a global presence customer proximity through a strong dealer network and industry leading solutions for profitable and sustainable agriculture 2 3 DEDICATED UNCOMPROMISED SMART For New Holland the year 2015 marks 120 years of innovations Since 1895 New Holland has been committed to providing SMART solutions that