Installation Remote Engine Start System Instructions -Books Pdf

INSTALLATION REMOTE ENGINE START SYSTEM INSTRUCTIONS
04 Jan 2020 | 30 views | 0 downloads | 18 Pages | 3.08 MB

Share Pdf : Installation Remote Engine Start System Instructions

Download and Preview : Installation Remote Engine Start System Instructions


Report CopyRight/DMCA Form For : Installation Remote Engine Start System Instructions



Transcription

4 VEHICLE PREPARATION, 1 Using a 10mm socket ratchet disconnect the negative. battery terminal FIGURE A,NOTE Do not disconnect the battery cable from the. battery post, 2 Open the glove box and press inward on the sides of. the glove box to disengage the retaining tabs from the. glove box inner cover Disconnect the strut from the. glove box FIGURE B, 3 Using a panel removal tool carefully remove the right. side dashboard panel by starting at the bottom access. notch and working upward to disengage four 4 pressure. clips FIGURE C, 4 Using a panel removal tool carefully lift upward to.
disengage 4 pressure clips and one 1 finger clip, and then pull rearward to remove the passenger s side. ornament panel FIGURE D, 5 Using a Phillips screwdriver remove seven 7 Phillips. screws secuing the glove box inner cover Disengage. the six 6 pressure clips and disconnect the glove box. lamp connector to remove the glove box inner cover. FIGURE D FIGURE E,PART NUMBER ISSUE DATE,SUBARU OF AMERICA 2 OF 9. H001SFL201 00 13 Feb 2017,5 REMOTE ENGINE START ECU MOUNTING. 1 Locate the factory immobilizer module and bracket. mounted near the upper left side of the passenger s. side dashboard Using alcohol clean the left side of the. immobilizer module bracket as shown FIGURE F,Clean with.
2 Remove the release liner from the remote engine, start ECU and attach it to the left side of the factory. immobilizer module bracket Ensure the bottom of the. remote engine start ECU is flush with the bottom of the. immobilizer module bracket as shown Press firmly in. place for at least 30 seconds FIGURE G,NOTE Ensure the remote engine start ECU. connectors will be facing toward the rear of the,Remote Engine. 3 Using one 1 of the supplied 39cm tie wraps secure. the remote engine start ECU to the immobilizer module. bracket Trim off the excess tie wrap FIGURE H,PART NUMBER ISSUE DATE. H001SFL201 00 13 Feb 2017,SUBARU OF AMERICA 3 OF 9.
6 PRE ARRANGED JUMPER HARNESS CONNECTIONS, 1 Locate and release the vehicle s 8 pin and 2 pin pre. fit connectors secured to the vehicle s wire harness. with breakaway tape near the upper right side of the. passenger s side dashboard FIGURE I, 2 When the vehicle s 8 pin and 2 pin pre fit connectors. are free from the breakaway tape unplug and discard. the 2 pin mating connector wire jumper This is used. for the power window interrupt circuit, 3 Plug the remote engine start pre arranged jumper. harness 8 pin and 2 pin connectors into the,corresponding pre fit connectors FIGURE J. 4 Route and secure the pre arranged jumper harness. to the vehicle s wire harness using three 3 of the CAUTIO. CAUTIO N DO NOT,CAUTIO N DO NOT BEND,CAUTIO N DO NOT BE.
supplied 20cm tie wraps at the white tape rings The N DO. tie wrap on the left is hidden from view Trim off the. excess tie wraps FIGURE K, 5 Plug the pre arranged jumper harness 12 pin connector. into the 12 pin white port on the remote engine start. ECU previously mounted to the left side of the factory. immobilizer module bracket Step 5 FIGURE K,PART NUMBER ISSUE DATE. SUBARU OF AMERICA 4 OF 9,H001SFL201 00 13 Feb 2017. 7 PANEL RE ASSEMBLY, 1 Re connect the glove box lamp connector to the lamp on the glove box inner cover Re install the glove box inner. cover by engaging the six 6 pressure clips and secure with seven 7 Phillips screws. 2 Re install the passenger s side ornament panel by engaging the four 4 pressure clips and one 1 finger clip. 3 Re install the right side dashboard panel by engaging the four 4 pressure clips. 4 Re install the glove box and strut, 5 At the end of the installation insert the Quick Reference Cards into the Owner s Information Kit.
8 UNDER HOOD WARNING LABEL MOUNTING, 1 Using alcohol clean the top of the air intake plenum. near the radiator core support, 2 Remove the release liner from the under hood warning. label and secure to the top of the air intake plenum. as shown FIGURE L,WARNING ADVERTISSEMENT,PART NUMBER ISSUE DATE. H001SFL201 00 13 Feb 2017,SUBARU OF AMERICA 5 OF 9. 9 HOOD SAFETY SWITCH MOUNTING, 1 In the engine compartment locate and release the 2 pin.
pre fit hood safety switch connector secured to the. vehicle s wire harness with breakaway tape in front of the. relay box on the passenger s side of the vehicle, 2 When the 2 pin pre fit hood safety switch connector is free. from the breakaway tape unplug and discard the 2 pin. mating connector, 3 Locate the vehicle s relay box mounted on the passenger s. side fender support Using a panel removal tool release. the relay box retaining tabs and remove it from the bracket. to provide access to the 10mm mounting bolt closest to. the front of the vehicle FIGURE N, 4 Remove the 10mm bolt securing the relay box bracket. closest to the front of the vehicle and discard Using the. supplied foam tape wrap the bottom of the relay box. bracket FIGURE O FIGURE N, NOTE The foam tape should be flush with the bottom. edge of the relay box bracket, 5 Using a 10mm socket ratchet mount the hood safety.
switch bracket behind the relay box bracket using the. supplied 10mm bolt FIGURE P, 6 Ensure that the supporting tongue on the hood safety. switch bracket is seated flat against the top of the fender. support while tightening the 10mm bolt FIGURE Q, 7 Using a 10mm socket torque wrench tighten the 10mm. bolt to 10 8 Nm 2 Nm 1 10 Kgf m 0 2 Kgf m 8 ft,lbs 1 5 ft lbs FIGURE O. T Supporting,FIGURE P FIGURE Q,PART NUMBER ISSUE DATE. SUBARU OF AMERICA 6 OF 9,H001SFL201 00 13 Feb 2017.
9 HOOD SAFETY SWITCH MOUNTING continued, 8 Securely mount snap in the supplied hood safety switch. into the bracket and plug the vehicle s pre fit 2 pin female. hood switch connector into the base of the hood safety. switch FIGURE R, 9 Using one 1 of the supplied 20cm tie wraps secure the. hood safety switch wire harness to the vehicle s relay box. bracket Trim off the excess tie wrap FIGURE S,PART NUMBER ISSUE DATE. H001SFL201 00 13 Feb 2017,SUBARU OF AMERICA 7 OF 9. 10 SYSTEM POWER UP, 1 After all the connections are complete re connect the vehicle s negative battery terminal Using a 10mm socket.
torque wrench tighten the 10mm nut to 7 5 Nm 2 Nm 0 76 Kgf m 0 2 Kgf m 5 5 ft lbs 1 5 ft lbs. 2 Start the vehicle at least one 1 time using the Access key prior to activating the remote engine start system This. is required to allow the vehicle s electronic systems to re synchronize. 3 With the vehicle running via the Access key verify that the instrument cluster airbag light turns off If the airbag light. remains on refer to the vehicle service information for troubleshooting. 4 Refer to the vehicle Owner s manual for the Power Window Reset Procedure to restore the power window functions. 11 SYSTEM REGISTRATION,DST i SETUP,Plug the DST i Press and hold the DST i. With an Access key,Using the arrows on the,B and A buttons. diagnostic plug inside the vehicle,DST i select Diagnostic. simultaneously for, into the vehicle s turn ON the ignition and Press A to proceed. approximately 5 seconds to Registration,diagnostic connector.
to enter stand alone mode,REGISTRATION, Using the arrows Using the arrows Using the arrows Using the arrows on. on the DST i select PRESS on the DST i select PRESS on the DST i select PRESS the DST i select the. Name A Impreza A Model year A vehicle model year,DST i screen will DST i screen will. Using the arrows Using the arrows,PRESS display Press YES if PRESS display Check if. on the DST i select on the DST i select A,A it is a smart system Ignition SW is. Immobilizer YES,otherwise press NO turned ON,DST i screen will.
Using the arrows Using the arrows,Using the arrows display Execute. PRESS on the DST i select PRESS on the DST i select. on the DST i select Remote Engine Start,A Remote Engine Start A. YES CM Registration,CM Registration,Press YES or NO. DST i screen will,display Successful Using the arrows. Remote Engine Start PRESS Registration,on the DST i select A.
CM Registration Complete,PART NUMBER ISSUE DATE,SUBARU OF AMERICA 8 OF 9. H001SFL201 00 13 Feb 2017,12 POST INSTALLATION CHECKLIST. 1 REMOTE ENGINE START Ensure the Access key is removed from the vehicle the engine hood all doors. and trunk are closed Press the START button on the remote start transmitter two 2 times within three. 3 seconds The vehicle s parking lights should flash and the vehicle s horn should honk one 1 time and. then the vehicle should crank and start Once started the transmitter LED will flash two 2 times and the. parking lights will turn on and stay on signifying the vehicle is running The transmitter LED will flash one. 1 time every three 3 seconds signifying the vehicle is still running. 2 SHUT DOWN WITH DOOR OPENING While the vehicle is running by the remote engine start wait at least. five 5 seconds and then confirm that all functions lock unlock trunk but not panic operate properly on. the FACTORY transmitter Once the FACTORY transmitter functionality is confirmed press the UNLOCK. button on the FACTORY transmitter and open any vehicle door The remote engine start should shut down. and the transmitter LED should flash three 3 times indicating the system has shut down. 3 ACTIVATION WITH DOOR OPEN Ensure the Access key is removed from the vehicle and the engine hood. and trunk are closed Open the driver s door and press the START button on the remote start transmitter two. 2 times within three 3 seconds The vehicle s parking lights should flash and the vehicle s horn should. honk six 6 times The vehicle should not start with any door or trunk opened. 4 BRAKE PEDAL SAFETY While sitting in the vehicle with the engine hood all doors and trunk closed. activate the remote engine start and press the brake pedal The vehicle should shut off. 5 HOOD SAFETY SWITCH Open the engine hood and activate the remote engine start The vehicle s parking. lights should flash and the vehicle s horn should honk two 2 times The vehicle should not start since the. hood safety switch is activated, 6 HEATER AC FUNCTION With the Access key inside the vehicle press the start button on the dashboard. two 2 times to turn ON the ignition Preset the vehicle s heater or air conditioning to the ON position Press. the start button on the dashboard one 1 time to turn OFF the ignition and remove the Access key from the. vehicle Activate the remote engine start and verify that the heater or air conditioning turns on to the preset. setting for manual climate controlled vehicles or turns to the Full Auto setting for electronic climate control. 7 15 MINUTE RUN TIME Activate the remote engine start and allow the system to run for the 15 minute. preset run time The remote engine start should shut down after 15 minutes 10 seconds. 8 TRANSMITTER FUNCTIONALITY VERIFICATION Activate the remote engine start using both of the. supplied single button remote start transmitters,FUNCTIONAL TESTING IS NOW COMPLETE. PART NUMBER ISSUE DATE,H001SFL201 00 13 Feb 2017,SUBARU OF AMERICA 9 OF 9.
4280703 Rev A 2 13 17,NUM RO DE PI CE H001SFL201,DESCRIPTION SYST ME DE D MARRAGE DISTANCE. LONGUE PORT E,INSTRUCTIONS IMPREZA CROSSTREK,D INSTALLATION. 1 CONTENU DE LA TROUSSE, Module de d marrage distance Faisceau cavalier pr mont Contacteur de s curit du. T l commandes de d marrage,UCE Quantit 1 capot support et boulon. distance avec tiquettes de mise,Quantit 1 Quantit 1.
REMOTE START QUICK REFERENCE, LONG RANGE ACTIVATION ALL MODELS ALTERNATE ACTIVATION. PUSH BUTTON START MODELS,Remote Start Activation,Remote Start Activation. Press Two 2 Times,Press Two 2 Times,Within 2 Seconds Then. Within Three 3 Seconds,Press and Hold For Three 3,Remote Start Shutdown Seconds. Press and Hold For,Remote Start Shutdown,Three 3 Seconds.
Press and Hold For,Two 2 Seconds, NOTE All vehicle doors hood trunk or rear gate must be closed prior to activating the remote engine start. system Any open entry point will prevent starting or cause the system to shut down. Upon successful activation the remote start fob will flash and beep one 1 time the horn will honk one 1 time. and the side marker lights tail lights and parking lights will flash one 1 time The system will check certain safety. preconditions before starting and if all conditions are met the engine will start within five 5 seconds After the. engine starts the remote start fob will flash and beep two 2 times the horn will honk one 1 time and the side. marker lights tail lights and parking lights will flash one 1 time While the engine is running via the remote engine. start system the remote start fob will continue to flash one 1 time every three 3 seconds the side marker lights. tail lights and parking lights will remain illuminated and the power window switches will be disabled The engine. will continue to run for fifteen 15 minutes unless one of the safety parameters below is triggered The system also. has a timer that will allow the system to operate for a maximum of twenty 20 minutes under multiple remote start. activations Using the factory ignition key Turn start models or Access key Push button start models to turn on the. ignition resets the twenty 20 minute timer, If the engine turns over but does not start or starts and stalls the remote engine start system will power off and then. attempt to start the engine three 3 additional times The system will not attempt to restart the engine if it determines. WARNING AVERTISSEMENT a vehicle malfunction is preventing it from starting If the engine does not start after the three 3 additional attempts. the remote engine start request will be aborted,Remote Start Safety Parameters. This vehicle is equipped with a remote controlled engine starter For safety and security reasons the system will fail to start or shut down the engine during remote start operation if. any of the following occur, To reduce the risk of serious Injury or death switch engine starter The remote start system has operated for twenty 20 minutes between ignition ON cycles. The horn will honk three 3 times and the parking lights will flash three 3 times. Any of the vehicle s doors trunk or rear gate are open. system into service mode and disconnect the vehicle battery. The horn will honk six 6 times and the parking lights will flash six 6 times. The vehicle s hood is open, The horn will honk two 2 times and the parking lights will flash two 2 times.
before performing any service on the vehicle The ignition key is resting in the ignition cylinder Turn start models. The horn will honk two 2 times and the parking lights will flash two 2 times. The transmission shifter is not in the park position. Ce v hicule est dot d un d marreur distance Pour r duire les. The horn will honk two 2 times and the parking lights will flash two 2 times. The vehicle s brake pedal is pressed before the vehicle ignition is turned ON. risques de blessures graves ou mortelles mettre le d marreur. The horn will honk two 2 times and the parking lights will flash two 2 times. The vehicle s engine idle speed has reached a level over 3 500 RPM this will cause the vehicle to shut down. The vehicle s security system is triggered by opening the door trunk or rear gate if the security system is armed. distance en mode service et d brancher la batterie du v hicule at the time of remote start activation. In addition to the items above if the vehicle s engine management system determines there is a safety risk due to a. avant d effectuer des travaux d entretien sur celui ci vehicle related problem the engine will shut down. WARNING TO AVOID DANGER OF CARBON MONOXIDE NEVER REMOTE START A VEHICLE IN A CLOSED. SPACE SUCH AS A CLOSED GARAGE, NOTE Laws in some communities require that the vehicle be within view of anyone using the Remote Engine. Start In some areas use of the Remote Engine Start may violate state provincial or local laws Before using. the Remote Engine Start check your state provincial and local laws. See the vehicle owner s manual for more details, Provided that the remote start fob is within the operating range of the system P N 4280648 Rev. tiquette de mise en Cartes de r f rence rapide Attaches autoblo Ruban mousse. garde du comparti Quantit 1 en anglais 1 en quantes Quantit 1. ment moteur fran ais 20 cm Quantit 6,Quantit 1 39 cm Quantit 1. 2 OUTILS REQUIS,Tournevis cruciforme,court et standard. Cl dynamom trique Outil de d pose de Coupe fils,panneau B A.
Interface diagnostic DST i SSM IV,Cl rochet douille de. 10 mm et rallonge Alcool et chiffon,3 SIGNIFICATION DES SYMBOLES. Enlever T Couple de serrage,D connecter,R utiliser. Emplacement de l attache ou de la vis, MISE EN GARDE N ATTACHEZ JAMAIS LE FAISCEAU DU D MARREUR DISTANCE DES FAISCEAUX OU DES CONNEC. TEURS JAUNES SYST ME DE COUSSINS GONFLABLES DANS LE V HICULE. NUM RO DE PI CE VERSION DATE,13 F v 2017,SUBARU OF AMERICA 1 DE 9.
H001SFL201 00,4 PR PARATION DU V HICULE, 1 l aide d une cl rochet douille de 10 mm d connectez la. borne n gative de la batterie FIGURE A, REMARQUE Ne d branchez pas le c ble de la borne de. la batterie, 2 Ouvrez la bo te gants et appuyez sur les c t s de la bo te. pour lib rer les languettes de retenue du couvercle int rieur. D gagez le support de la bo te gants FIGURE B, 3 l aide de l outil de d pose de panneau enlevez d licatement. le c t droit du tableau de bord en partant de l encoche. d acc s du bas vers le haut pour lib rer les quatre 4 attaches. 4 l aide de l outil de d pose de panneau soulevez d licatement FIGURE B. pour lib rer quatre 4 attaches pression et une 1 attache. griffe puis tirez vers l arri re pour retirer le panneau de. garniture c t passager FIGURE D, 5 l aide du tournevis cruciforme retirez les sept 7 vis qui.
maintiennent la bo te gants dans le couvercle int rieur. Lib rez les six 6 attaches pression et d branchez le. connecteur de la lampe de la bo te gants pour retirer le. couvercle int rieur FIGURE E,FIGURE D FIGURE E,NUM RO DE PI CE VERSION DATE. H001SFL201 00 13 F v 2017 SUBARU OF AMERICA 2 DE 9. 5 INSTALLATION DE L UCE DU D MARREUR DISTANCE, 1 Rep rez le module de l antid marreur d origine et le support. mont s du c t sup rieur gauche du tableau de bord c t. passager l aide d alcool nettoyez le c t gauche du support. du module de l antid marreur comme illustr FIGURE F. 2 Retirez l endos adh sif de l UCE du d marreur distance. et apposez le sur le c t gauche du support du module de. l antid marreur d origine Assurez vous que le bas de l UCE du. d marreur distance est galit avec le bas du support du. module de l antid marreur comme illustr Appuyez fermement. pendant au moins 30 secondes FIGURE G, REMARQUE Assurez vous que les connecteurs de l UCE. du d marreur distance sont orient s vers l arri re du. UCE du d mar,reur distance, 3 Au moyen d une 1 des attaches autobloquantes de 39 cm. fournies assujettissez l UCE du d marreur distance au. support du module de l antid marreur Coupez l exc dent des. attaches FIGURE H,NUM RO DE PI CE VERSION DATE,13 F v 2017.
SUBARU OF AMERICA 3 DE 9,H001SFL201 00,6 CONNEXIONS DU FAISCEAU CAVALIER PR MONT. 1 Rep rez et d gagez les connecteurs pr mont s 8 et. 2 broches fix s au faisceau de c blage du v hicule par du. ruban d tachable pr s du c t sup rieur droit du tableau de. bord c t passager FIGURE I, 2 Lorsque les connecteurs pr mont s 8 et 2 broches sont. d gag s du ruban d tachable d branchez le cavalier. connecteur homologue 2 broches et mettez le au rebut Il. est destin au circuit de coupure du l ve glace lectrique. 3 Branchez les connecteurs 8 et 2 broches du faisceau. cavalier pr mont du d marreur distance dans les,connecteurs pr mont s correspondants FIGURE J. 4 Acheminez le faisceau cavalier pr mont et assujettissez le. au faisceau de c blage du v hicule au moyen de trois 3. des attaches autobloquantes de 20 cm fournies au niveau CAUTIO. CAUTIO N DO NOT,CAUTIO N DO NOT BEND, du ruban blanc L attache autobloquante de gauche n est pas BEND. CAUTIO N DO NOT BE,visible Coupez l exc dent des attaches FIGURE K.
5 Branchez le connecteur 12 broches du faisceau cavalier. pr mont dans la prise blanche 12 broches de l UCE du. d marreur distance pr c demment mont du c t gauche. du support du module de l antid marreur tape 5 FIGURE. NUM RO DE PI CE VERSION DATE, H001SFL201 00 13 F v 2017 SUBARU OF AMERICA 4 DE 9. 7 R ASSEMBLAGE DU PANNEAU, 1 Rebranchez le connecteur de la lampe sur le couvercle int rieur de la bo te gants Installez le couvercle int rieur de la bo te. gants au moyen des six 6 attaches pression et fixez le l aide de sept 7 vis cruciformes. 2 Installez le panneau de garniture c t passager l aide de quatre 4 attaches pression et d une 1 attache griffe. 3 Installez le panneau du c t droit du tableau de bord l aide des quatre 4 attaches pression. 4 Installez la bo te gants et le support, 5 la fin de l installation glissez les Cartes de r f rence rapide dans le dossier du propri taire. 8 TIQUETTE DE MISE EN GARDE DU COMPARTIMENT MOTEUR. 1 En utilisant de l alcool nettoyez la partie sup rieure de. la chambre d admission d air proximit du support de. faisceau de radiateur, 2 Retirez l endos adh sif de l tiquette de mise en garde du. compartiment moteur et collez la sur le haut de la chambre. d admission d air comme illustr FIGURE L,WARNING ADVERTISSEMENT.
NUM RO DE PI CE VERSION DATE,13 F v 2017,SUBARU OF AMERICA 5 DE 9. H001SFL201 00,SUPPORT DU CONTACTEUR DE S,9 CURIT DU CAPOT. 1 Dans le compartiment moteur rep rez et lib rez le connecteur. 2 broches pr mont du contacteur de s curit du capot qui est. fix au faisceau de c blage du v hicule par du ruban d tachable. l avant de la bo te de relais du c t passager FIGURE M. 2 Lorsque le connecteur 2 broches du contacteur de s curit du. capot est d gag du ruban d tachable d branchez le et mettez. au rebut le connecteur homologue 2 broches, 3 Rep rez la bo te de relais du v hicule situ e sur le support de FIGURE M. l aile c t passager l aide de l outil de d pose de panneau. d gagez les languettes de retenue de la bo te de relais et retirez. les pour acc der au boulon de 10 mm le plus pr s de l avant du. v hicule FIGURE N, 4 Retirez le boulon de 10 mm le plus pr s de l avant du v hicule. qui retient le support de la bo te de relais et mettez le au rebut. l aide du ruban mousse fourni enveloppez le bas du support. de la bo te de relais FIGURE O, REMARQUE Le ruban mousse doit tre affleurant avec le.
rebord inf rieur du support de la bo te de relais FIGURE N. 5 l aide de la cl rochet douille de 10 mm installez le contacteur. de s curit du capot derri re le support de la bo te de relais en. utilisant le boulon de 10 mm fourni FIGURE P, 6 Lorsque vous serrez le boulon de 10 mm assurez vous que la. languette de soutien sur le support du contacteur de s curit du. capot est bien plat contre le haut du support de l aile FIGURE. 7 l aide de la cl rochet douille rallonge de 10 mm serrez le. boulon 10 8 2 Nm 1 10 0 2 kgf m 8 1 5 lb pi,T Languette. de soutien,FIGURE P FIGURE Q,NUM RO DE PI CE VERSION DATE. H001SFL201 00 13 F v 2017 SUBARU OF AMERICA 6 DE 9.


Related Books

APPLICATION FOR LICENSE AS A NURSING HOME ADMINISTRATOR

APPLICATION FOR LICENSE AS A NURSING HOME ADMINISTRATOR

for Long Term Care Administrators (NAB) examination upon completion of the A.I.T. program. A temporary permit for the AIT program shall cover a period of, at least, six (6) months. If you are eligible for a limited permit, please complete the attached "Administrator-in-Training" forms. These forms must be signed by your preceptor and notarized ...

CONTINUITY OF OPERATIONS PLAN TEMPLATE

CONTINUITY OF OPERATIONS PLAN TEMPLATE

CONTINUITY OF OPERATIONS PLAN TEMPLATE CAHF-DPP Page 4 of 34 INTRODUCTION PURPOSE This template, written for long-term care facilities, is designed to assist providers in developing an effective continuity of operations (COOP) plan for emergency scenarios that result in an interruption in services and/or operations. Long-term

On Essential Spectrum of a Class of Singular Integral ...

On Essential Spectrum of a Class of Singular Integral

On Essential Spectrum of a Class of Singular Integral Operators R. U. VERMA Courant Institute of Mathematical Sciences, New York University, New York, New York 10012 Submitted by K. Fan 1. INTRODUCTION Schwartz [ 111 located the essential spectrum of a class of singular integral operators in the space L,[O, 11. The results thus obtained are ...

CORPORATE FINANCE - GBV

CORPORATE FINANCE GBV

corporate finance a south african perspective edited by gideon els elda du toit i pierre erasmus i liezel kotze i sam ngwenya kevin thomas i suzette viviers

2009 CAPITAL - Langford

2009 CAPITAL Langford

Attachments: Presentation to City of Langford.doc I understand from you that the Association should not be making a verbal presentation to the Administration and Finance Committee, but that a written presentation could be included in the package made available to its members, and that it would also be taken into account

South African investment management: Preparing for disruption

South African investment management Preparing for disruption

An examination of te global investment management industry 6 While there is a global movement to adopt Blockchain-operated investment management solutions, this is still not widely adopted in South Africa. While the South African government does not view Bitcoin (which was the starting point of Blockchain technology) as a legal form of

Use of StatSeal Advanced Disc to Decrease Time to ...

Use of StatSeal Advanced Disc to Decrease Time to

with a radial artery compression device called the Terumo (TR) Band (a dual compression balloon device) and 300 patients were treated with a chitosan-based pad (a carbohydrate derivative chitin). Their study found a significant difference in compression time and lower rates of radial artery occlusion favoring the chitosan-based pad [4]. A ...

Coastal Planning Strategies for Adaptation to Sea Level ...

Coastal Planning Strategies for Adaptation to Sea Level

project is in the planning phase or the potential for development is high. Specific sites are selected in considera- tion of their development potential and the existence of current development plans. This research suggests mul- tiple planning and design strategies for adaptation suitable for each of these target regions: multi-tiered terraces

PROPOSAL FRANCHISE SUPERWASH LAUNDRY

PROPOSAL FRANCHISE SUPERWASH LAUNDRY

SuperWash Laundry merupakan laundry low cost pertama dan terbesar di Indonesia. Hanya dengan paket investasi yang rendah sudah bisa membuka usaha franchise laundry Tim Profesional dan Terlatih SuperWash Laundry mempunyai tim support dan manajemen yang profesional dan tentunya sudah terlatih di bidangnya, sehingga

Get - dca.org.uk

Get dca org uk

a special gift or album, or ... designing artwork in a weekend with our knowledgeable staff. ... and Photosho p/InDesign. Introduction to