Installation Instructions Abt Electronics-Books Pdf

Installation Instructions Abt Electronics
01 Aug 2020 | 10 views | 0 downloads | 14 Pages | 456.59 KB

Share Pdf : Installation Instructions Abt Electronics

Download and Preview : Installation Instructions Abt Electronics

Report CopyRight/DMCA Form For : Installation Instructions Abt Electronics



Transcription

Installation Instructions, How to Install, 1 Identify the wall sleeve brand for your installation from the chart below. Wall Sleeve Dimensions, Width Height Depth, White Westinghouse 25 1 2 15 1 4 16 17 1 2 or 22. Frigidaire 25 1 2 15 1 4 16 17 1 2 or 22, Carrier 52F Series 25 1. 2 15 4 16 17 1 2 or 22, General Electric Hotpoint 26 15 5 8 15 7 8. Whirlpool 25 7 8 16 1 2 17 1 8 or 23, Fedders Emerson 27 16 3 4 16 3 4 or 19 3 4.
Sears Kenmore 25 3 4 16 7 8 18 5 8, Emerson Fedders 26 3 4 15 3 4 15. Carrier 51S Series 25 3 4 16 7 8 18 5 8, Friedrich 27 16 3 4 16 3 4. For larger sleeves an adaptor trim kit EA120T is available. All wall sleeves used to mount the new Air Conditioner must be in sound structural condition and have a rear. grille that securely attaches to sleeve or rear flange that serves as a stop for the Air Conditioner. For new installations a Frigidaire Sleeve Kit EA108T is recommended. When installation is complete replacement unit MUST have a rearward slope as shown in Fig 1. 2 Remove old Air Conditioner from wall sleeve and prepare wall sleeve as follows. Clean interior do not disturb seals, Wall sleeve must be securely fastened in wall before installing Air Conditioner Drive more nails or screws through. sleeve into wall if needed, Retouch wall sleeve painted surface if needed. 3 If not existing drill a 3 16 clearance hole for grounding screw through left side of wall sleeve in a clear area about. 3 inches maximum back from front edge of sleeve using grounding screw and toothed washer Pull loose end. of ground wire out front of sleeve and temporarily bend it down and around lower edge of sleeve Fig 2 This. ground wire will later be attached to frame of air conditioner once it is installed. 1 4 to 5 16, sleeve Max, Wall sleeve to unit, sleeve grounding Hole.
UNIT FRONT, Fig 1 Fig 2, Installation Instructions. 4 Prepare the wall sleeve for installation of the new unit per the following Brand instructions. 1 Emerson 15 Deep, 2 Fedders 19 3 4 Deep, 3 Fedders or Friedrich 16 3 4 Deep. 4 General Electric Hotpoint 16 7 8 Deep, 5 Sears or Carrier 51S Series 18 5 8 Deep. 6 Whirlpool 17 1 8 Deep, 7 Whirlpool 23 Deep, 8 White Westinghouse Frigidaire 16 17 1 2 Deep. Carrier 52F Series, 9 White Westinghouse Frigidaire 22 Deep.
5 Identify your wall sleeve type and follow the instructions for that type in the following pages. This unit s increased performance characteristics result from having two rear air intakes. It is very important that these installation instructions are followed so your unit can operate at maximum. efficiency, If there is an existing sleeve and there is an existing rear grille it needs to be replaced by one that has been. shipped with the unit in the accessory kit, FOR INCREASED EFFICIENCY UTILIZE THE PROVIDED LOUVERED REAR PANEL. Installation of new grille provided with unit, 1 Remove the existing grille. 2 Place the grille included with the new air conditioner towards the rear of the sleeve. 3 Mark through the hole positions, 4 Drill through the sleeve flanges with a 1 8 drill bit. 5 Attach the new grille with self threading screws and washers not included. 6 It is VERY IMPORTANT that the grille is placed exactly as shown. 7 Most decorative exterior grilles may be left in place as long as the proper interior air direction grille is installed. NOTE If the provided grill is not used it may lead to product damage and possible failure. Installation Instructions, Wall Sleeve Brands, 1 Emerson 15 Deep.
1 Remove existing rear grille as shown on Page 3 of this manual and Rear Louvers. replace with provided louvered rear panel Install as shown here 4 5 4. NOTE You may need to drill holes in flange of existing sleeve to match 80 80. new rear grille, 2 Attach 1 1 x 3 8 x 25 long seal in the center at the top of the sleeve. Remove the backing paper and press into position, 3 Attach 2 1 x 3 8 x 14 seals to the left and right sides of the sleeve. 4 Cut 2 1 x 3 8 x 25 long seals to 14 long each and attach to the. vertical sections of the grille as shown, 5 Attach 2 4 1 2 x 3 1 2 x 1 1 2 centering support blocks one on each. side wall Place in center of side wall with the tapered end facing the. 6 Gently slide unit into sleeve, 7 Before sliding all the way back remove 2nd screw from fron on left. side of unit, 8 Remove the plastic washer from the screw.
9 Screw and attach the other end of the ground wire from sleeve to the. unit as shown in picture Make sure that the toothed washer is against. the cabinet, 10 Slide the unit completely to the rear to ensure a good seal making. sure the ground wire does not become tangled, 11 Seal Frame the unit as described on the last page of these. instructions, 12 If you have difficulty with mounting the grill to the sleeve follow the. instructions for direct mounting on Page 13, Installation Instructions. Wall Sleeve Brands, 2 Fedders 19 3 4 Deep, 1 Remove existing rear grille as shown on Page 3 of this manual and Rear Louvers.
replace with provided louvered rear panel Install as shown here 4 5 4. NOTE You may need to drill holes in flange of existing sleeve to match 80 80. new rear grille, 2 Attach 2 4 1 2 x 3 1 2 x 1 1 2 centering support blocks one on each. side wall Place in center of side wall with the tapered end facing the. 3 Cut 2 17 Tapered Spacer Blocks as shown below into two pieces. 3 4 Tapered Spacer Block, protection Paper Backing. 4 The 4 section is placed in front of the rib on base with the tapered. end facing the back of the sleeve The remaining portion will be placed. behind the rib again sloping toward the rear of the sleeve This helps. induce a rearward slope on the unit, 5 Attach 1 1 x 3 8 x 25 long seal in the center at the top of the sleeve. Remove the backing paper and press into position, 6 Attach 2 1 x 3 8 x 14 seals to the left and right sides of the sleeve. 7 Cut 2 1 x 3 8 x 25 long seals to 14 long each and attach to the. vertical sections of the grille as shown, 8 Gently slide unit into sleeve.
9 Before sliding all the way back remove 2nd screw from front on left. side of unit, 10 Remove the plastic washer from the screw. 11 Screw and attach the other end of the ground wire from sleeve to the unit. as shown in picture Make sure that the toothed washer is against the. 12 Slide the unit completely to the rear to ensure a good seal making sure. the ground wire does not become tangled, 13 Seal Frame the unit as described on the last page of these instructions. 14 If you have difficulty with mounting the grill to the sleeve follow the. instructions for direct mounting on Page 13, Installation Instructions. Wall Sleeve Brands, 3 Fedders or Friedrich 16 3 4 Deep. 1 Remove existing rear grille as shown on Page 3 of this manual and Rear Louvers. replace with provided louvered rear panel Install as shown here 4 5 4. NOTE You may need to drill holes in flange of existing sleeve to match 80 80. new rear grille, 2 Attach 2 4 1 2 x 3 1 2 x 1 1 2 centering support blocks one on each.
side wall Place in center of side wall with the tapered end facing the. 3 Cut 2 17 Tapered Spacer Blocks as shown below into two pieces. Tapered Spacer Block 1, Cut Here 12 1 2 2 1 2, protection Paper Backing. 4 The 2 1 2 section is placed in front of the rib on base with the tapered. end facing the back of the sleeve Cut the remaining portion to 12 1 2. and place behind the rib again sloping toward the rear of the sleeve. This helps induce a rearward slope on the unit, 5 Attach 1 1 x 3 8 x 25 long seal in the center at the top of the sleeve. Remove the backing paper and press into position, 6 Attach 2 1 x 3 8 x 14 seals to the left and right sides of the sleeve. 7 Cut 2 1 x 3 8 x 25 long seals to 14 long each and attach to the. vertical sections of the grille as shown, 8 Gently slide unit into sleeve. 9 Before sliding all the way back remove 2nd screw from front on left side. 10 Remove the plastic washer from the screw, 11 Screw and attach the other end of the ground wire from sleeve to the unit.
as shown in picture Make sure that the toothed washer is against the. 12 Slide the unit completely to the rear to ensure a good seal making sure. the ground wire does not become tangled, 13 Seal Frame the unit as described on the last page of these instructions. 14 If you have difficulty with mounting the grill to the sleeve follow the. instructions for direct mounting on Page 13, Installation Instructions. Wall Sleeve Brands, 4 General Electric Hotpoint 16 7 8 Deep. 1 Remove existing rear grille as shown on Page 3 of this manual and Rear Louvers. replace with provided louvered rear panel Install as shown here 4 5 4. NOTE You may need to drill holes in flange of existing sleeve to match 80 80. new rear grille, 2 Cut 2 17 Tapered Spacer Blocks as shown below into two pieces. 3 4 Tapered Spacer Block Cut Here, protection Paper Backing.
3 Install as shown with the tapered end 1 2 from the back of the sleeve. This helps induce a rearward slope on the unit, 4 Attach 1 1 x 3 8 x 25 long seal in the center at the top of the sleeve. Remove the backing paper and press into position, 5 Attach 2 1 x 3 8 x 14 seals to the left and right sides of the sleeve. 6 Cut 2 1 x 3 8 x 25 long seals to 14 long each and attach to the. vertical sections of the grille as shown, 7 Center unit gently slide unit into sleeve. 8 Before sliding all the way back remove 2nd screw from front on. left side of unit, 9 Remove the plastic washer from the screw. 10 Screw and attach the other end of the ground wire from sleeve to the unit. as shown in picture Make sure that the toothed washer is against the. 11 Slide the unit completely to the rear to ensure a good seal making sure. the ground wire does not become tangled, 12 Seal Frame the unit as described on the last page of these instructions.
13 If you have difficulty with mounting the grill to the sleeve follow the. instructions for direct mounting on Page 13, Installation Instructions. Wall Sleeve Brands, 5 Sears or Carrier 51S Series 18 5 8 Deep. 1 Remove existing rear grille as shown on Page 3 of this manual and Rear Louvers. replace with provided louvered rear panel Install as shown here 4 5 4. NOTE You may need to drill holes in flange of existing sleeve to match 80 80. new rear grille, 2 Install 2 tapered spacer blocks to the floor of the sleeve as shown. This helps induce a rearward slope on the unit, 3 Install as shown with the tapered end 1 2 from the back of the sleeve. This helps induce a rearward slope on the unit, 4 Attach 1 1 x 3 8 x 25 long seal in the center at the top of the sleeve.
Remove the backing paper and press into position, 5 Attach 2 1 x 3 8 x 14 seals to the left and right sides of the sleeve. 6 Cut 2 1 x 3 8 x 25 long seals to 14 long each and attach to the. vertical sections of the grille as shown, 7 Center unit gently slide unit into sleeve. 8 Before sliding all the way back remove 2nd screw from front on left. side of unit, 9 Remove the plastic washer from the screw. 10 Screw and attach the other end of the ground wire from sleeve to the. unit as shown in picture Make sure that the toothed washer is against. the cabinet, 11 Slide the unit completely to the rear to ensure a good seal making. sure the ground wire does not become tangled, 12 Seal Frame the unit as described on the last page of these instructions.
13 If you have difficulty with mounting the grill to the sleeve follow the. instructions for direct mounting on Page 13, Installation Instructions. Wall Sleeve Brands, 6 Whirlpool 17 1 8 Deep, 1 Remove existing rear grille as shown on Page 3 of this manual and Rear Louvers. replace with provided louvered rear panel Install as shown here 4 5 4. NOTE You may need to drill holes in flange of existing sleeve to match 80 80. new rear grille, 2 Cut 2 17 Tapered Spacer Blocks as shown below into two pieces. Tapered Spacer Block 1, Cut Here protection Paper Backing. 3 Install to the floor of the sleeve as shown This helps induce a rearward. slope on the unit, 4 Attach 1 1 x 3 8 x 25 long seal in the center at the top of the sleeve.
Remove the backing paper and press into position, 5 Attach 2 1 x 3 8 x 14 seals to the left and right sides of the sleeve. 6 Cut 2 1 x 3 8 x 25 long seals to 14 long each and attach to the. vertical sections of the grille as shown, 7 Center unit gently slide unit into sleeve. 8 Before sliding all the way back remove 2nd screw from front on left. side of unit, 9 Remove the plastic washer from the screw. 10 Screw and attach the other end of the ground wire from sleeve to the unit. as shown in picture Make sure that the toothed washer is against the. 11 Slide the unit completely to the rear to ensure a good seal making sure. the ground wire does not become tangled, 12 Seal Frame the unit as described on the last page of these instructions. 13 If you have difficulty with mounting the grill to the sleeve follow the. instructions for direct mounting on Page 13, Installation Instructions.
Wall Sleeve Brands, 7 Whirlpool 23 Deep, 1 Remove existing rear grille as shown on Page 3 of this manual and Rear Louvers. replace with provided louvered rear panel Install as shown here. 4 5 50 50 4, NOTE You may need to drill holes in flange of existing sleeve to match 80 80. new rear grille, Because of the increased unit depth first try dry fitting using. Note that the air conditioner dimensions are 24 wide 14 high and 19 deep without front Install Air Conditioner according to these installation instructions to achieve the best performance Save these installation instructions for future reference Do This First for existing sleeve You may not need all parts in the kit Discard unused parts Items in Kit 2020213A1639 Hardware 2 2 3

Related Books

KIT COMPONENTS 99 4544 Abt Electronics

KIT COMPONENTS 99 4544 Abt Electronics

99 4544 INSTALLATION INSTRUCTIONS Lumina APV 1990 95 19 Lumina APV 1996 brake release Remove the dash trim bezel 1

FULL MANUAL Abt Electronics

FULL MANUAL Abt Electronics

ABOUT THIS MANUAL The user manual has two parts this simple paper USER MANUAL and a detailed FULL MANUAL you can download USER MANUAL See this manual for safety instructions product installation components connections and product specifications FULL MANUAL You can access the Full Manual on Samsung s on line customer

Impacts cologiques des Technologies de l Information et

Impacts cologiques des Technologies de l Information et

Impacts cologiques des Technologies de l Information et de la Communication On place beaucoup d espoir dans la capacit des TICs faciliter cette n cessaire transition vers une soci t durable Pour qu un tel espoir soit l gitime encore faut il au pr alable disposer d une image aussi compl te que non complaisante des impacts environnementaux des mat riels lectroniques

The Impact of Information Technology on the Auditing

The Impact of Information Technology on the Auditing

Key Words Information Technology Expectations Gap Audit Risk Audit Fees Audit Standards Introduction Perhaps it is obvious to recall that the auditing profession was born and will continue to be a social profession serve the community in which they operate and are affected by it as consistently affect or uneven unchanged if the accounting profession which is the act of making the

Impact of Information Technology in Human Resources Management

Impact of Information Technology in Human Resources Management

Impact of Information Technology in Human Resources Management 35 technological advancement human and cultural factors play a more important role than before However technology is often seen by management as essential means to compete in the global market To that technology including information technology brings the desired results the most important issue for an organization is how to

Impact of Information Technology on Teaching Learning Process

Impact of Information Technology on Teaching Learning Process

Information technology is a set of tools that can help the right people with the right information at the right time This paper highlights the importance of IT in educational sector impact of IT on classroom teaching advantages and disadvantages of IT Key Words Information Technology Teaching learning process Communication Internet Computer Introduction Today knowledge and

Frequently Asked Questions for International College Bound

Frequently Asked Questions for International College Bound

bylaws specifically NCAA Bylaw 14 3 Frequently Asked Questions for International College Bound Student Athletes Page No 2 core course GPA of 2 200 In addition a minimum number of approved core courses Divisions I and II require 16 core courses must be achieved which will be equivalent to a country s academic credential presented And finally proof of graduation must be

www intra focus com

www intra focus com

Rule 2 27 14 defines and lists characteristics of a defenseless player HELMETS The helmet is intended to protect the player from head injuries It must therefore be fitted properly so that it does not come off through play Coaches equipment managers and athletic trainers must be

7029

7029

Branche in JEDDAH 300 Million EGP Consolidated Revenues AMER RESTAURANTS 3 Index A Game Changer In The Region About Amer Group Holding Company 6 Where it All Began Brand Heritage 8 The Concept Behind The Place Where everyday is FRESH 10 4 HALKET EL SAMAK What s On The Menu A culinary experience like no other 14 A Welcoming Ambience Redefining hospitality 16 The Evolution Of Success Brand

365 2012 Simple Version Control of SAS Programs and SAS

365 2012 Simple Version Control of SAS Programs and SAS

Paper 365 2012 Simple Version Control of SAS A complete discussion is beyond the scope of this paper but we shall discuss general considerations for version control of SAS programs data sets and outputs deploying Subversion and examples how SAS processes and tools can be integrated to draw upon Subversion functionality and facilities The result is a very functional environment that