Dpu31 Spu16 Holmatro-Books Pdf

DPU31 SPU16 Holmatro
26 May 2020 | 21 views | 0 downloads | 60 Pages | 1.30 MB

Share Pdf : Dpu31 Spu16 Holmatro

Download and Preview : Dpu31 Spu16 Holmatro


Report CopyRight/DMCA Form For : Dpu31 Spu16 Holmatro



Transcription

All rights reserved You are prohibited from copying or reproducing this manual any. materials contained herein or any portion hereof in any manner whatsoever without the. express prior written consent of Holmatro, Holmatro reserves the right to change the contents of this manual at any time without prior. notice Holmatro also reserves the right to change any part or component of any machine. referenced in this manual at any time without prior notice. This manual is intended for use solely with the basic version of each piece of equipment and. each product referenced and should not be used in connection with any modified altered or. adapted version of any piece of equipment without the express prior written consent of. Additional information on adjustments maintenance and repair of any product contained. herein will be provided upon written request of the technical department of your supplier If. not provided contact Holmatro directly, EXCEPT AS EXPRESSLY SET FORTH ON THE ENCLOSED WARRANTY CARD. HOLMATRO MAKES NO OTHER WARRANTY OR REPRESENTATION EITHER. EXPRESS OR IMPLIED WITH RESPECT TO THE STATEMENTS CONTAINED. HEREIN HOLMATRO HEREBY EXCLUDES ANY AND ALL IMPLIED. WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY AND. FITNESS FOR A PARTICULAR PURPOSE, IN NO EVENT WILL HOLMATRO BE LIABLE FOR DIRECT INDIRECT. SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF. USE OF THIS MANUAL OR ANY STATEMENTS CONTAINED THEREIN. SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES. OR LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE. ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. IF ANY PROVISION CONTAINED HEREIN SHALL BE UNLAWFUL VOID OR. FOR ANY REASON UNENFORCEABLE THEN THAT PROVISION SHALL BE. SEVERED FROM THE STATEMENT AND SHALL NOT AFFECT THE VALIDITY. AND ENFORCEABILITY OF THE REMAINING STATEMENTS CONTAINED. 1 Introduction, We congratulate you on this purchase Be sure to read and understand this user manual before using the. tool This user manual covers the basic aspects for the safe use and operation of this equipment. First of all check that your equipment is complete and undamaged Notify your Holmatro dealer. immediately if the equipment is damaged or incomplete and do not use the equipment. The equipment is designed for use by professional fully trained fire and rescue personnel. This pump is suitable only for operating double acting hydraulic rescue equipment with mineral oil. hydraulic fluid to an allowable pressure of 720 bar 10 500 psi These pumps come with Core. Technology as standard, Follow these instructions to ensure your safety and to keep your equipment in good condition.
2 Safety Symbols, THIS IS THE SAFETY ALERT SYMBOL IT IS USED TO ALERT YOU TO. POTENTIAL PERSONAL INJURY HAZARDS OBEY ALL SAFETY, MESSAGES THAT FOLLOW THIS SYMBOL TO AVOID POSSIBLE INJURY. DANGER indicates an imminently hazardous situation. which if not avoided will result in death or serious. WARNING indicates a potentially hazardous situation. which if not avoided could result in death or serious. CAUTION indicates a potentially hazardous situation. which if not avoided may result in minor or moderate. CAUTION used without the safety alert symbol indicates a. potentially hazardous situation which if not avoided may. result in property damage,3 Safety Instructions, Study these instructions carefully before operating this. Never use a Core Technology product with a Twin line hose product. Use this equipment only for jobs for which it is designed If in doubt or not clear be sure to consult. your Holmatro dealer, Always wear personal protection equipment such as safety goggles helmet gloves protective. clothing and safety shoes,Keep spectators at sufficient distance.
In the event of oil leakage stop immediately and consult the troubleshooting list. In the event of unfamiliar noise vibration or other unusual behavior stop immediately and consult. your Holmatro dealer, The equipment must only be operated with non toxic mineral base hydraulic oil distributed by. Use only original Holmatro accessories and parts,Observe the maintenance instructions. Only trained service technicians certified by Holmatro are allowed to repair this equipment. Replace safety symbols pictograms and or information labels if worn illegible damaged or. Always place the pump on a stable firm base which is free of protrusions or loose matter gravel. Use the pump at a minimum distance of 3 feet 1 metre from buildings structures. Never use the pump in an enclosed space and always ensure sufficient ventilation. Never inhale the exhaust gas It contains Carbon Monoxide a colorless and odorless gas which can. cause loss of consciousness or death, Keep the exhaust discharge free of foreign objects. Never refill fuel when the engine is running,Never refill or even use near open fire. Fill the fuel tank to the sight glass level Never overfill. Remove fuel spillage before starting the engine, Never lift the pump with chains or steel wire ropes on the carrying handle.
The vehicle or object must be stabilized before beginning any extrication technique. Never use the relief device tool on pressurized hoses valve blocks or rescue tools that are attached to. an operating power unit The pressure relief device is designed for use only on hoses that are. disconnected from the pump unit See section 7 2 3,4 Operation. The pump is a Personal Power pump The compact design and light weight make it easy for one. person to carry The DPU31 runs a two stage axial piston pump that can build up a maximum. pressure of 720 bar 10 500 psi and can run two rescue tools at the same time The SPU16 runs a. three stage axial piston pump that can build up a maximum pressure of 720 bar 10 500 psi The. SPU16 runs one tool only,5 Description Model DPU31. 5 1 Product identification, A Fuel tank cap vent lever G Hydraulic oil level indicator M Recoil starter. B Hydraulic oil fill cap H Fuel level indicator N Engine on off switch. C Fuel cap I Bypass valve O ECO switch, D Carrying handle J LED indicator panel P Maintenance cover. E Spark plug service cover K Core couplers female Q Choke. F Muffler L Hydraulic oil drain plug,O N M L K K,5 2 Technical specifications.
Allowable operating pressure 10 500 psi 720 bar,Hydraulic oil contents 2 90 qt 2740 cc. Usable hydraulic oil contents 2 74 qt 2590 cc, Dimensions LxWxH 23 5 8 x 11 7 16 x 16 600 x 290 x 425 mm. Weight ready for use Core 55 lbs 25 kg,Temperature range 4 F to 176 F 20 C to 80 C. Engine model Honda GX100, Engine type 4 stroke overhead camshaft single cylinder. Displacement 6 0 cu in 98cc, Engine speed 4550 rpm with Eco Throttle switch off.
3000 4550 rpm with Eco Throttle switch on,Engine oil capacity 0 42 qt 400 cc. Fuel tank capacity 1 32 qt 1250 cc,Fuel Unleaded gasoline Octane 86 or higher. Cooling system Forced air,Ignition system Full transistor. Spark plug CR5HSB NGK,6 Description Model SPU16,6 1 Product identification. A Fuel tank cap vent lever G Hydraulic oil level indicator M Recoil starter. B Hydraulic oil fill cap H Fuel level indicator N Engine on off switch. C Fuel cap I Bypass valve O ECO switch, D Carrying handle J LED indicator panel Behind cover.
E Spark plug service cover K Core coupler female P Choke. F Muffler L Hydraulic oil drain plug,6 2 Technical specifications. Allowable operating pressure 10 500 psi 720 bar,Hydraulic oil contents 1 79 qt 1700cc. Usable hydraulic oil contents 1 78 qt 1680 cc,Dimensions LxWxH 20 x 10 x 15 522 x 260 x 388 mm. Weight ready for use Core 36 8 lbs 16 7 kg,Temperature range 4 F to 176 F 20 C to 80 C. Engine model Honda GXH50, Engine type 4 stroke overhead camshaft single cylinder.
Displacement 3 05 cu in 50cc, Engine speed 5500 rpm with Eco Throttle switch off. 4000 5500 rpm with Eco Throttle switch on,Engine oil capacity 0 26 qt 250 cc. Fuel tank capacity 1 06 qt 1000cc,Fuel Unleaded gasoline Octane 86 or higher. Cooling system Forced air,Ignition system Full transistor. Spark plug CR5HSB NGK,7 Controls,Engine Switch,To start and stop the engine.
Switch Position,OFF or 0 To stop the engine,ON or 1 To start the engine. NOTE The engine switch also closes the fuel line between the fuel tank and the carburetor. Recoil Starter, To start and stop the engine pull the starter cord lightly until resistance is felt then pull fast. NOTE Do not allow the starter handle to snap back against the pump Let the handle return gently. to prevent damage,Fuel tank cap, The fuel cap is supplied with a vent that can be closed A. to seal the fuel tank The vent lever must be in the. ON position for the engine to run,NOTE When the engine is not in use set the vent. lever to the OFF position to prevent fuel leakage,Allow the engine to cool before turning the vent.
lever to the OFF position,LED indicator panel, The pump is supplied with a LED panel that will indicate. when one of the following conditions exists,Engine oil low. The engine has a level switch that turns the engine off. automatically if one of the following conditions occurs. The engine oil level is too low,The pump is inclined at an angle greater than. 20 degrees to the horizontal surface DPU31, After the level switch has turned off the engine the red. LED A will come on for a while If you attempt to restart the engine without adding engine oil or. leveling the pump the red LED A will come on again. Overheating, The pump has an oil temperature sensor If overheating.
occurs the red LED B will first flash If the maximum. temperature is exceeded the engine will turn off and the. red LED B will remain on for some time, The pump has an indicator that shows when it is time for SPU16. the next service When the service time is due the green. LED C will flash Contact your Holmatro dealer for maintenance of the pump The service light. will not cause the engine to turn off but it will continue to flash until service is performed. Choke lever, The choke is used to provide proper fuel air mixture for. starting the engine when cold The choke lever is moved. manually to the appropriate position Move the choke. lever to CHOKE position to enrich the mixture for cold. starting Move the choke lever to the RUN position after. the engine has warmed up or the engine begins to run. irregularly To re start a warm engine the choke lever. may be left in the RUN position,Ecothrottle switch. The Ecothrottle automatically reduces the engine to low RPM s when the attached tool s are not. operating When a tool is operated the engine speed increases to provide the proper speed to power. the tool s The Ecothrottle switch for the SPU16 is located behind the maintenance cover See. product ID section 6 1,ON Press switch C to position B The. Ecothrottle is activated and will increase the,engine speed when a tool is used When a.
tool is not in use the Ecothrottle reduces the,engine speed to low RPM and lower noise. levels and fuel consumption,OFF Press the switch C to position A The. Ecothrottle does not operate and the engine,speed remains at the maximum. Pressure bypass valve, If it is not possible to disconnect the hydraulic hose from the pump when the attached tool is in the. neutral position the pressure can be released using the bypass valve A located near each Core. female coupler B on the pump,Turn the engine off,Turn screw A on the bypass valve clockwise.
to the OPEN position until it stops This will,release the pressure. Disconnect the affected hose s from the pump,Turn the screw A counterclockwise to the. CLOSED position,Contact your Holmatro Dealer for service. 8 Operation, The oil from the hydraulic pump is supplied to the tool via high pressure hoses The oil returns at. atmospheric pressure to the pump if the tool dead man s handle is in the neutral position. Tool Control Handle decal, Oil is admitted under the tool piston if the dead man s handle is in the open position The tool will then.
open The oil above the piston flows back to the pump. Oil is admitted above the tool piston if the dead man s handle is in the close position The tool will. close The oil under the tool piston flows back to the pump. The tool dead man s handle always returns to the neutral position when released. CORE TOOLS PUMPS, The hydraulic system in the unit is provided with a safety valve This safety valve prevents excessive. pressure in the tool if the return line to the pump is blocked Never change the setting of this safety valve. Oil will discharge from the rear of the tool if the return hose becomes blocked while the pump is running. If this happens first switch the pump engine motor to OFF and disconnect the hose Then connect a new. When Holmatro valve blocks are mounted on your Holmatro power unit the manual operated. release valve is no longer needed As soon as the hose is connected oil is flowing through the hose s inner. shell and returning back to the tank of the pump through the hose s outer shell When a rescue tool with. the adaptor installed has been connected to the hose oil will flow into the tool To change from. one rescue tool to another the user simply disconnects the rescue tool from the hose and connects the. alternate rescue tool to the hose Oil always flows from the female coupler into the male coupler for. Holmatro reserves the right to change the contents of this manual at any time without prior notice Holmatro also reserves the right to change any part or component of any machine referenced in this manual at any time without prior notice This manual is intended for use solely with the basic version of each piece of equipment and each product referenced and should not be used in connection

Related Books

Li M Chen Zhixun Su Bo Jiang Mathematical Problems in

Li M Chen Zhixun Su Bo Jiang Mathematical Problems in

Mathematical Problems in Data Science Theoretical and Practical Methods Mathematical Problems in Data Science Li M Chen Zhixun Su Bo Jiang Mathematical Problems in Data Science Theoretical and Practical Methods 123 Li M Cheng Department of Computer Science and Information Technology The University of the District of Columbia Washington DC USA Bo Jiang School of Information

This File Has Been Downloaded From WordPress com

This File Has Been Downloaded From WordPress com

Mathematical problems in image processing partial differemial equations and file calculus of variations Gilles Aubcrt Pierre Komprobst p cm Applied mathematical sciences 147 Includes bibliographical references and index ISBN 11 387 95326 4 alk paper I Image processing Mathematics I Kornprobst Pierre ll Title Ill Applied mathematical sciences ISpringer Veriag New York

ICTP L Free

ICTP L Free

ICTP L e ctur Notes SCHOOL ON MA THEMA TICAL PR OBLEMS IN IMA GE PR OCESSING 4 22 Septem b er 2000 Editor Charles E Chidume The Ab dus Salam ICTP T rieste Italy SCHOOL ON MA THEMA TICAL PR OBLEMS IN IMA GE PR OCESSING First edition Cop yrigh t c 2000 b y The Ab dus Salam In ternational Cen tre for Theoretical Ph ysics The Ab dus Salam ICTP has the irrev o cable and inde nite

Mathematics in Image Processing cs cas cz

Mathematics in Image Processing cs cas cz

Mathematics in image processing Mathematics in image processing CV etc My subjective importance Linear algebra 70 Numerical mathematics mainly optimization 60 Analysis including convex analysis and variational calculus 50 Statistics and probability basics machine learning 30 Graph theory mainly graph algorithms 15

REPORTAGE Tchernobyl avant l oubli

REPORTAGE Tchernobyl avant l oubli

Tchernobyl avant l oubli LE MONDE BOUGE L bas leur pr sence a tonn Des artistes Pascal Rueff en t te ont r sid deux mois quelques kilom tres de la centrale En t moins de l apr s catastrophe a se passe un 1er avril et on pourrait croire une vaste blague quand un inconnu nomm Pascal Rueff se met nous parler d une r sidence d artistes en banlieue de

Consensus Scientifique sur l Accident Nucl aire de Tchernobyl

Consensus Scientifique sur l Accident Nucl aire de Tchernobyl

Title Consensus Scientifique sur l Accident Nucl aire de Tchernobyl Author GreenFacts ASBL VZW Subject Accident Nucl aire de Tchernobyl Created Date

Tchernobyl effets sanitaires et environnementaux

Tchernobyl effets sanitaires et environnementaux

Incendies pr s de Tchernobyl Criirad

Incendies pr s de Tchernobyl Criirad

Tchernobyl incendies CRIIRAD 1 7 Communiqu CRIIRAD du 8 avril 2020 16H Incendies Tchernobyl 29 cours Manuel de Falla 26000 Valence Incendies pr s de Tchernobyl De nombreux incendies en Ukraine y compris en zone contamin e Le territoire Ukrainien est parcouru actuellement par de nombreux incendies

Les cons quences en Suisse 20 ans apr s l accident

Les cons quences en Suisse 20 ans apr s l accident

Tchernobyl calcul es pour les diff rentes classes d ge Le respect des recommandations mises l poque a conduit essentiellement pour les enfants en bas ge une r duction de dose d environ 0 8 mSv 1 10 100 1 0 m S v valeur moyenne valeur pour la population de la r gion la plus touch e valeur extr me hypoth tique adultes enfants de 10 ans enfants de moins de 2 ans

Tchernobyl download pro arte tv

Tchernobyl download pro arte tv

Tchernobyl TrenTe ans de radioacTiviT Une soir e Thema en forme de bilan dans l ombre de la centrale nucl aire sinistr e Mardi 26 avril ShakeSpeare Comme il vouS plaira Freedom hoSpital un roman graphique Syrien UNE COPRODUCTION aRTE a U CIN ma LE 6 avRIL les grands rendez voussaMEDi 23 avril vENDrEDi 29 avril 2016 sp cial shakespeare Le g nial po te et dramaturge s