B Sc Course First Semester University Of Babylon College -Books Pdf

B Sc Course First Semester University of Babylon College
27 Dec 2019 | 27 views | 0 downloads | 14 Pages | 1.89 MB

Share Pdf : B Sc Course First Semester University Of Babylon College

Download and Preview : B Sc Course First Semester University Of Babylon College


Report CopyRight/DMCA Form For : B Sc Course First Semester University Of Babylon College



Transcription

Chapter Five Solid Waste Management Assit Prof Dr Nabaa Shakir Hadi. In some residence waste compactors are being used to reduce the volume of waste to be. collected Compacted wastes are usually placed in waste containers or in sealed plastic bags. There are number of different collection system with and without recycling and many others. Two residential waste separation system are compared in example 5 1. Example 5 1 Comparison of residential waste separation programs. The effectiveness of residential waste separation programs depends on the type of system used. for the collection of separated wastes A number of communities use a collection system in. which three containers are used for recycled materials in addition to one or more containers for. non recyclable materials In the three container system system1 newspaper is placed in one. container Aluminum cans glass and plastics are placed in the second container The. remaining wastes are placed in the third container The separated materials placed in special. containers are collected at the curb, In another system system2 four containers areused All paper and cardboard materials are. placed in one container All plastic glass tin cans aluminum and any other metals are placed. in a second container Garden wastes are placed in the third container and all remaining waste. materials are placed in the fourth container Compare these two systems assume newspaper. represents 25 percent of the total amount of paper. Determine realistically how much of the waste stream can be separated for recycling using the. two systems described above Assume 80 percent of the available material is separated and the. participation rate is 100 percent An estimate of the amount of solid waste that can be separated. using the above system is presented in the following table. Chapter Five Solid Waste Management Assit Prof Dr Nabaa Shakir Hadi. From Table 1, Waste components that are to be recycled are shown in bold. Based on 80 percent recovery with 100 percent participation If only 50 percent of the homes participate the. recycling rate drops to about 9 6 percent, Based on 80 percent recovery with 100 percent participation If only 50 percent of the homes participate the. recycling rate drops to about 33 2 percent,Container number. Comment as shown in above computation table the amount of material separated for recycling. with system1 is 19 2 percent versus 66 4 percent for system2 If the participation rate were to. drop to 50 percent the corresponding amounts are 9 6 versus 33 2percent using system1 it. will be difficult to achieve the 25 percent recycling goal without a high degree of homeowner. participation Additional separation possibly at a MRF will be required to reach the 50 percent. goal by the year 2000 Using system both the 25 and 50 percent diversion goals are achievable. with a reasonable amount of homeowner participation. At Low and Medium Rise Apartments, Handling methods in most low and medium rise apartment buildings resemble those used.
for low rise dwellings but methods may vary somewhat depending on the waste storage. Chapter Five Solid Waste Management Assit Prof Dr Nabaa Shakir Hadi. location and collection method Typical solid waste storage locations include basement storage. outdoor storage and occasionally compactor storage. At High Rise Apartments, In high rise apartment buildings the most common methods of handling solid wastes involve. one or more of the following, 1 Wastes are picked up by building maintenance personnel or porters from the various floors. and taken to the basement or service area, 2 Wastes are taken to the basement or service area by tenants or. 3 Wastes usually bagged are placed by the tenants in specially designed vertical chutes. usually circular with openings located on each floor see Fig 5 3. Wastes discharged in chutes are collected in large containers compacted into large containers. or baled directly Recyclable materials may be put outside in the hall or entry way for pickup or. they may be taken by the tenants to the service area located on each floor for pickup The. entrance to the waste chute is usually located in the service area Bulky items are usually taken. to the service area by the tenants or the building maintenance crew. Fig 5 3 Typical chute openings for the discharge of waste materials in high rise apartment. buildings a isometric view of waste chute opening on individual floor and b outdoor. type used in some older high rise apartment building. Chutes for use in apartment buildings are available in diameters from 12 to 36 in The most. common size is 24 in diameter All the available chutes can be furnished with suitable intake. In some of the more recent apartment building developments underground pneumatic. transport system have been used in conjunction with the individual apartment chutes The. Chapter Five Solid Waste Management Assit Prof Dr Nabaa Shakir Hadi. underground pneumatics system are used to transport the wastes from the chute discharge. points in each building to a central location for storage in large containers or onsite processing. Both air pressure and Vacuum transport systems have been used in this application. Fig 5 4 Pneumatic transport systems for solid wastes. 5 2 Storage Of Solid Wastes At The Source, Factors that must be considered in the onsite storage of solid wastes include. 1 The effects of storage on the waste components,2 The type of container to be used.
3 The container location and,4 Public health and aesthetics. 1 Effects of storage on waste components, An important consideration in the onsite storage of wastes are the effects of storage itself on. the characteristics of the wastes being stored These effects of storing wastes include. a Biological decomposition,b The absorption of fluids and. c The contamination of waste components, a Biological decomposition or Microbiological Decomposition. Food and other wastes placed in on site storage containers will almost immediately start to. undergo microbiological decomposition often called putrefaction as a result of the growth of. bacteria and fungi If wastes are allowed to remain in storage containers for extended periods of. time flies can start to breed and odorous compounds can develop. Chapter Five Solid Waste Management Assit Prof Dr Nabaa Shakir Hadi. b Absorption of fluids, Because the components that comprise solid wastes have differing initial moisture contents.
re equilibration takes place as wastes are stored onsite in containers Where mixed wastes are. stored together paper will absorb moisture from food waste sand fresh garden trimmings The. degree of adsorption that takes place depends on the length of time the waste are stored until. collection,c Contamination of waste components, Perhaps the most serious effect of onsite storage of wastes is the contamination that occurs. The major waste components may be contaminated by small amounts of wastes such as motor. oils household cleaners and paints The effect of this contamination is to reduce the value of. the individual components for recycling,2 Types of Containers. To a large extent the types and capacities of the containers used depend on. a The characteristics and types of solid wastes to be collected. b The type of collection system in use,c The collection frequency and. d The space available for the placement of containers. Because solid waste is collected manually from most residential low rise detached dwellings. the container should be light enough to be handled easily by one collector when full Injuries to. collectors have resulted from handling containers that were loaded too heavy Table5 1 gives. data on the types of containers and advantages and disadvantages of each. Chapter Five Solid Waste Management Assit Prof Dr Nabaa Shakir Hadi. Table5 1 Data on the types of containers and advantages and disadvantages of each. 3 Container Storage Locations, Container storage locations depends on the type of the dwelling or commercial and industrial. facilities the available space and access to collection services. 4 Public Health and Aesthetics, Although residential solid wastes account for a relatively small proportion of the total wastes.
generated in the United States 10 to 15 percent they are perhaps the most important because. they are generated in areas with limited storage space As a result they can have significant. public health and aesthetic impacts, Public health concerns are related primarily to the infestation of areas used for the storage of. solid wastes with vermin and insects that often serve as potential disease vectors By far the. most effective control measure for both rats and flies is proper sanitation Typically proper. sanitation involves,The use of containers with tight lids. The periodic washing of the containers as well as of the storage areas and. Chapter Five Solid Waste Management Assit Prof Dr Nabaa Shakir Hadi. The periodic removal of biodegradable materials usually within less than 8 days which is. especially important in areas with warm climates, Aesthetic considerations are related to the production of odors and the unsightly conditions. that can develop when adequate attention is not given to the maintenance of sanitary. conditions, Most odors can be controlled through the use of containers with tight lids. Maintenance of a reasonable collection frequency, If odors persist the contents of the container can be sprayed with a masking deodorant as a.
temporary expedient, To maintain aesthetic conditions the container should be scrubbed and washed periodically. 5 3 Processing Of Solid Wastes At Residential Dwellings. Waste processing is used to,1 Reduce the volume,2 Recover usable materials or. 3 Alter the physical form of the solid wastes, The most common onsite processing operations used at low rise detached residential dwellings. include food waste grinding component separation compaction incineration in fireplaces. and composting,Grinding of Food Wastes, Food waste grinders are used primarily for wastes from the preparation cooking and serving. of foods Most grinders sold for home use cannot be used for large bones or other bulky items. Functionally grinders render the material that passes through them suitable for transport. through the sewer system Because the organic material added the wastewater has resulted in. overloading many treatment facilities it has been necessary in some communities to forbid the. installation of waste food grinder in new developments until additional treatment capacity. becomes available, Where food waste grinders are used extensively the weight of waste collected per person will.
tend to be lower In terms of the collection operation the use of home grinders does not have a. significant impact on the volume of solid wastes collected In some cases where grinders are. used it has been possible to increase the time period between collections pickups because. wastes that might readily decay are not stored see figure5 5. Chapter Five Solid Waste Management Assit Prof Dr Nabaa Shakir Hadi. Fig 5 5 kitchen home grinders,Separation of Wastes. The question that must be answered is what is the energy content of residual solid waste. The effect of home separation on the energy content of the residential MSW is considered in. example5 2, Example5 2 Effect of home separation of waste on energy content of as collected residential. MSW Using the computation table prepared in example3 3 re produced below estimate the. energy content in Btu Ib of the remaining solid wastes if 60 percent of the paper and 90 percent. of the cardboard are separated by the homeowner,From Table1. From Table 2, Chapter Five Solid Waste Management Assit Prof Dr Nabaa Shakir Hadi. 1 The total energy content of 100 Ib of solid waste with the composition given in Table 2 4 is. equal to 505 530 Btu, 2 Determine the energy content and weight of 60 percent of the paper in the original sample.
a Energy content 60 pape,b Weight 60 paper 0 60 34 Ib 20 4 Ib. 3 Determine the energy content and weight of 90 percent of the cardboard in the original. a Energy content 90 paper 0 90 42 000 Btu 37 800 Btu. b Weight 90 paper 0 90 6 Ib 5 4 Ib, 4 determine the total energy content weight and energy content per pound of the original. sample after paper and cardboard have been separated. a Total energy after recovery,b Total weight after recovery. c Energy content of waste per Ib after separation,in original sample. Comment in this example the removal by weight of approximately 26 percent of the wastes. reduced the per pound energy content of the original sample by approximately 14 percent. Compaction, To reduce the volume of solid wastes that must be handled compaction units commonly are.
installed in larger apartment buildings Typically a compactor is installed at the bottom of a. solid waste chute Wastes falling through the chute activate the compactor by means of. photoelectric cells or limit switches The compressed wastes may be formed into bales or. extruded and loaded automatically into metal containers or paper bags. Example5 3 Effect of home compactors on volume of collected solid wastes. Assume that home compaction units are to be installed in a residential area Estimate the. volume reduction that could be achieved in the solid wastes collected if the compacted specific. weight is equal to 540 Ib yd3 and the data given in Tables 1 and table 3 1 are applicable. 1 Set up a computation table to determine the volume of wastes as discarded in containers. using the data given in Table1 and 3 1, Chapter Five Solid Waste Management Assit Prof Dr Nabaa Shakir Hadi. Data from Table1,Data from Table3 1, Cardboard partially compressed by hand before being placed in waste compactor. Components not usually placed in home waste compactors. Total excluding components not usually placed in home waste compactors. 2 Determine the volume of compacted wastes excluding yard wastes wood metals other than. aluminum and tin cans and dirt ashes etc, 3 Determine the volume reduction for the compressible material. 4 Determine the overall volume reduction achieved with a home compactor taking into. account garden trimmings wood metals other than aluminum and tin cans dirt ashes etc. Chapter Five Solid Waste Management Assit Prof Dr Nabaa Shakir Hadi. Comment When the overall volume reduction is assessed the significance of a home. compactor is reduced This finding is especially true as the percentages of the components not. compacted such as garden trimmings increase,Composting. It is an effective way of reducing the volume and altering physical composition of solid. wastes while at the same time producing a useful by product A variety of methods are used. depending on the amount of space available and the wastes to be composted Composting can. be a significant factor in the computation to determine the quantity of waste diverted from. Backyard Composting, The simplest backyard composting method involves placement of material to be composted.
in a pile and occasionally watering and turning it to provide moisture and oxygen to the. microorganisms within the pile During composting period which can take up to year the. material placed in the pile undergo bacterial and fungal decomposition until only a humus. material known as compost remains The composted material which is biologically stabilized. can be used as a soil amendment or as a mulching material See figures below. Fig5 6 a Rotary and horizontal composter b Composted materials. Combustion, Chapter Five Solid Waste Management Assit Prof Dr Nabaa Shakir Hadi. In the past the burning of combustible materials in fireplaces and the burn of rubbish in. backyard incinerators was common practice Backyard incinerator is now banned in most parts. of the country, 5 4 Processing Of Solid Wastes At Commercial And Industrial Facilities. Onsite processing operations carried out at commercial industrial facilities generally similar to. those described for residential sources,Compaction. The baling of waste cardboard at markets and other commercial establishments is quite. common The bales vary in size baled cardboard is reprocessed for the production of packing. materials or shipping overseas for remanufacture into a variety of products. Shredding and Hydro pulping, Shredding is used most common in commercial establishments and by governmental agencies. to destroy sensitive documents that are no longer of value In some cases the volume of wastes. has been observed to increase after shredding, Although hydro pulping systems work well they are expensive and typically involve discharge.
to the local wastewater collection system Because the discharged of pulped material increases. the organic loading on local treatment facilities use of pulverizers may be restricted if. treatment capacity is limited,Fig5 7 Hydro pulping. Chapter Five Solid Waste Management Assit Prof Dr Nabaa Shakir Hadi.


Related Books

Volume 63 / Number 1 / SPRING 2014 - masonichomeny.org

Volume 63 Number 1 SPRING 2014 masonichomeny org

2 THE EMPIRE STATE MASON MAGAZINE Brotherly Love, Charity and Integrity SPRING 2014 E ven though this will be my final message to you, let it be

DASAR-DASAR FARMAKOLOGI 1 - Kemdikbud

DASAR DASAR FARMAKOLOGI 1 Kemdikbud

Bahan ajar /buku ini, diperuntukkan bagi siapa saja yang ingin mendalami dan memahami tentang dasar-dasar farmakologi. Sebagaimana telah dijelaskan di atas,Standar Kompetensi ini merupakan kompetensi yang banyak dibutuhkan pada bidang kesehatan.Buku ini dapat dipelajarai oleh siswa yang bergelut di bidang

NEWSLETTER FOR THE REDWOOD EMPIRE MODEL T CLUB

NEWSLETTER FOR THE REDWOOD EMPIRE MODEL T CLUB

NEWSLETTER FOR THE REDWOOD EMPIRE MODEL T CLUB ... Museum June 14, 2014 ... and The Vintage Magazine. Redwood Empire Model T Club

Empire State Building - STRUCTURE magazine

Empire State Building STRUCTURE magazine

frame of the Empire state Building is thus relatively low, in comparison ... Drawing courtesy of Architectural Forum Magazine, June 1930 ...

THE EMPIRE STATE MASON MAGAZINE - masonichomeny.org

THE EMPIRE STATE MASON MAGAZINE masonichomeny org

2 THE EMPIRE STATE MASON MAGAZINE Pride in Freemasonry FALL 2013 A ... 2014 in the Daniel D. Tompkins ... June 30th will be a special day for

Documentation 101 - Part Lien Perfection: Business Collateral

Documentation 101 Part Lien Perfection Business Collateral

Your State Association Presents. Lenders Learn. TM. Chapter 4. Loan Documentation 101 - Part 2. Lien Perfection: Business Collateral. Program Materials . Use this document to follow along with the webinar.

Street Names - In Alphabetical Order

Street Names In Alphabetical Order

Street Names - In Alphabetical Order MC-ID NO. Street Name. Location. District / Area County. Type. Aalto Place Sumter - Unit 692 (Villa San Antonio) 1 Sumter County Villa Abaco Path Sumter - Unit 197 9 Sumter County Unit Abana Path Sumter - Unit 206 9 Sumter County Unit Abasco Court Sumter - Unit 821 (Mangrove Villas) 8 Sumter County Villa

33 bite-size teacher-tested print-friendly ideas and in ...

33 bite size teacher tested print friendly ideas and in

simple, easy to understand language ActIonAblE tIpS & ADvIcE ... ESL CHEAT SHEETS (GRAMMAR EDITION). PUBLISHED BY BUSYTEACHER.ORG How to Teach the Present Simple

EVALUATING TRADE MARK DILUTION FROM THE PERSPECTIVE OF THE ...

EVALUATING TRADE MARK DILUTION FROM THE PERSPECTIVE OF THE

by the legal establishment, dilution was gradually translated into a state and then federal cause of action, providing trade mark proprietors with an alternative to consumer confusion upon which to base infringement proceedings. 16 The present-day anti-dilution provision in the United States protects marks that are

TABLE OF CONTENTS - Turner Ashby Knights Boys Soccer

TABLE OF CONTENTS Turner Ashby Knights Boys Soccer

In Volume 1 of Total Soccer Conditioning: A Ball-Oriented Approach, we provided a thorough set of ball-oriented exercises and drills that focus on a specific component of conditioning. For example, in the Chapter on Strength Training, we showed how lunges can be coupled with one-touch passing to enhance lower-body strength.